Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 80

Страница: 80 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

ENGINE GOVERNOR CONTROLLER (EGC) REMOVAL AND REPLACEMENT

PROCEDURE

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized

repairs performed on this equipment may result in danger to the technician or machine operator and will

invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety

notes and precautions detailed throughout this manual. If for any reason you do not understand the test

procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department

for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This procedure will aid the technician in the removal and replacement of the Engine Governor Controller

(EGC).

MATERIALS NEEDED

Slotted Screwdriver

Wiring Diagram

REMOVAL PROCEDURE

Turn off the engine on the SAE-300 HE machine.

Open the left side cover.

Label and disconnect plugs J1 and J2 from the engine governor controller. See

Figure F.31

. See

Wiring Diagram.

Using a slotted screwdriver, remove the two screws, standoffs, nuts and two washers securing the

electronic governor controller to the rear of the front panel. See

Figure F.31

The

engine governor controller (EGC)

can now be replaced.

REPLACEMENT PROCEDURE

Carefully position the new engine governor controller (EGC) into the machine.

Using a slotted screwdriver, attach the two screws, standoffs, nuts and two washers securing the

electronic governor controller to the rear of the front panel.

Connect plugs J1 and J2 to the engine governor controller. See Wiring Diagram.

Close the left side cover.

Perform the

Retest After Repair Procedure

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 80 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: