Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 74

Страница: 74 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

GENERATOR ARMATURE REMOVAL AND REPLACEMENT PROCEDURE

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized

repairs performed on this equipment may result in danger to the technician or machine operator and will

invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety

notes and precautions detailed throughout this manual. If for any reason you do not understand the test

procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department

for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This procedure will aid the technician in the removal and replacement of the Welding Generator Armature.

MATERIALS NEEDED

Rope Sling

Miscellaneous Hand Tools

Wiring Diagram

REMOVAL PROCEDURE

Turn off the engine on the SAE-300 HE machine.

Perform the

Alternator Rotor Removal Procedure

Perform the

Alternator Stator Removal Procedure

Perform the

Generator Frame Removal Procedure

Using the rope sling, support the armature. Position the sling at the center of gravity of the

armature assembly. See

Figure F.28

Remove the eight screws securing the blower paddle segments and the outer diameter of the

flexible coupling disk to the flywheel.

With the armature securely supported in the sling, unlock it from the flywheel by carefully rotating

it 1/8 of a turn in either direction.

REPLACEMENT PROCEDURE

Carefully inspect the mating surfaces of the flywheel and armature coupling parts. These surfaces

must be clean and undamaged.

Support the armature in a rope sling and carefully move it into position and align it to the flywheel.

Rotate the armature 1/8 of a turn, in either direction, to engage the locking mechanism and line up

the bolt holes. Be certain that the coupling plate is fully and cleanly seated in the flywheel.

Replace the eight screws and four blower segments. Tighten the screws.

Perform the

Generator Frame Replacement Procedure

Perform the

Alternator Stator Replacement Procedure

Perform the

Alternator Rotor Replacement Procedure

Perform the

Retest After Repair Procedure

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 74 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: