Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 32

Страница: 32 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

If there is any evidence that the brushes may have been sticking in the brush holders, a new brush

holder and brush assembly should be installed.

Cleaning slip rings:

In the event that the slip rings have become dirty, discolored or mildly pitted, it will be necessary to

clean them using very fine (500 or 600 grit) emery cloth or a 220 or 320 grit commutator stone.

Commutator stones should only be used by experienced technicians who have the knowledge and

equipment necessary to use them safely.

Seating brushes:

If brushes have been replaced, repositioned, or are not making full contact with the slip rings, it will

be necessary to re-seat them. This can be done by placing a strip of 180 grit sandpaper between the

slip rings and the brushes, with the abrasive side against the brushes. Pull the sandpaper strip

around the circumference of the slip rings in the direction of rotor rotation only. Repeat this

procedure until the surface of each brush is in full contact with its matching slip ring.

Use low pressure compressed air to thoroughly blow the carbon, commutator stone and sandpaper

dust from the machine before operating.

Securely connect the leads to the brush terminals (See Wiring Diagram) and replace the alternator

cover if testing and service is complete.

Figure F.7 – Brush locations

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 32 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: