Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 27

Страница: 27 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

Observe Safety Guidelines

detailed in the beginning of this manual.

TROUBLESHOOTING GUIDE

PROBLEMS

(SYMPTOMS)

POSSIBLE AREAS OF

MISADJUSTMENT(S)

RECOMMENDED

COURSE OF ACTION

ENGINE PROBLEMS

The engine cranks when the

start button is pressed, but will

not start.

1. Make sure the run/stop

switch is in the run position.

2. The run/stop switch may

have been left in the run

position for more than 30

seconds (60 seconds on some

models). Move switch to the

stop position, then after a few

seconds, move it back to the

run position.

3. If the machine is being used

in a cold climate, the

thermostat or glow plug system

may need to be used. See the

welder's operator manual and

the engine operator’s manual

for detailed instructions.

4. Check that there is an

adequate supply of fresh clean

fuel and that the fuel shut-off

valve is open.

5. Check and if necessary,

replace the fuel filter.

6. There may be air in the fuel

system. See the engine

manufacturers manual and

bleed all air from the fuel

system.

1. Perform the

Engine

Governor Controller (EGC) Test

Procedure

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, contact the

Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 27 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: