Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 19

Страница: 19 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

Observe Safety Guidelines

detailed in the beginning of this manual.

TROUBLESHOOTING GUIDE

PROBLEMS

(SYMPTOMS)

POSSIBLE AREAS OF

MISADJUSTMENT(S)

RECOMMENDED

COURSE OF ACTION

OUTPUT PROBLEMS

There is no or very low weld

output. Auxiliary output is

normal.

1. Check that the remote/local

switch is positioned correctly.

2. If a remote current control is

being used, try switching to

local control. The remote

current control may be faulty.

3. Check all leads and cables

for damaged or poor

connections.

1. Perform the

Shunt Field Coil

Resistance And Ground Test

Procedure

2. Perform the

Shunt Field

Circuit Voltage Test Procedure

3. Perform the

Welding

Generator Brush And

Commutator Inspection And

Service Procedure

4. Check for damaged or poor

connections at the brush

holders, series and interpole

coils, coarse current control

unit, weld output terminals and

all the conductors connecting

these components.

5. Perform the

Weld Circuit

Ground And Short Circuit Test

Procedure

6. The armature may be faulty.

There is no auxiliary voltage at

receptacles but weld output is

normal.

1. Check that the auxiliary

power circuit breakers are not

tripped.

2. If the machine is equipped

with a ground fault circuit

interrupter (GFCI), it may be

tripped or defective.

NOTE:

GFCIs will not reliably

reset, unless engine is

operating at high idle RPM.

3. Check all leads and cables

for damaged or poor

connections.

1. Check for auxiliary voltage at

the receptacle input terminals;

if normal voltage is present,

replace terminals.

2. Check for auxiliary voltage at

the connections closest to the

exciter stator windings. See

Wiring Diagram.

• If normal voltage is present,

check the wiring and circuit

breakers between the test

points and the receptacle.

Repair or replace any defective

parts or wiring.

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, contact the

Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 19 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: