Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 78

Страница: 78 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

CURRENT SENSE BOARD REMOVAL AND REPLACEMENT PROCEDURE

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized

repairs performed on this equipment may result in danger to the technician or machine operator and will

invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety

notes and precautions detailed throughout this manual. If for any reason you do not understand the test

procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department

for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This procedure will aid the technician in the removal and replacement of the Current Sense Board.

MATERIALS NEEDED

Phillips Screwdriver

Wiring Diagram

REMOVAL PROCEDURE

Turn off the engine on the SAE-300 HE machine.

Open the left side cover.

Label and disconnect the plug from the current sense board. See

Figure F.30

. See Wiring Diagram.

Label and disconnect the four quick connect terminals securing leads to the current sense board.

See Wiring Diagram.

Using a Phillips screwdriver, remove the two screws securing the current sense board to the rear of

the front panel.

The current sense board can now be removed and replaced.

REPLACEMENT PROCEDURE

Carefully position the new current sense board into the machine.

Using a Phillips screwdriver, attach the two screws securing the current sense board to the rear of

the front panel.

Connect the four quick connect terminals securing leads to the current sense board. See Wiring

Diagram.

Connect the previously disconnected plug to the current sense board. See Wiring Diagram.

Close the left side cover.

Perform the

Retest After Repair Procedure

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 78 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: