Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 57

Страница: 57 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

Table F.1 – Electronic governor control (EGC) tests

(POS) TEST POINT (NEG) TEST POINT EXPECTED READING

MACHINE CONDITION

PLUG J1 PIN 9

CHASSIS GROUND

12 VDC

RUN/STOP SWITCH IN THE RUN

POSITION.

PLUG J2 PIN 7

CHASSIS GROUND

12 VDC

IDLER SWITCH IN THE LOW IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION.

PLUG J2 PIN 7

CHASSIS GROUND

MEG OHMS

IDLER SWITCH IN THE LOW IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION.

PLUG J2 PIN 7

CHASSIS GROUND

0 VDC

IDLER SWITCH IN THE HIGH IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION.

PLUG J2 PIN 7

CHASSIS GROUND

.4 OHMS

IDLER SWITCH IN THE HIGH IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION. MACHINE OFF.

PLUG J1 PIN 5

PLUG J1 PIN 8

4.7 VDC

IDLER SWITCH IN THE HIGH IDLE

POSITION. MACHINE RUNNING.

PLUG J1 PIN 5

PLUG J1 PIN 8

4.7 OHMS

IDLER SWITCH IN THE HIGH IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION. MACHINE OFF.

PLUG J1 PIN 3

PLUG J1 PIN 10

2.6 KHZ

IDLER SWITCH IN THE LOW IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION. MACHINE RUNNING.

PLUG J1 PIN 3

PLUG J1 PIN 10

3.2 KHZ

IDLER SWITCH IN THE HIGH IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION. MACHINE RUNNING.

PLUG J2 PIN 4

CHASSIS GROUND

2.6 VDC

IDLER SWITCH IN THE HIGH IDLE

POSITION. RUN/STOP SWITCH IN THE

RUN POSITION. MACHINE RUNNING.

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 57 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: