Lincoln Electric SAE-300 HE Скачать руководство пользователя страница 46

Страница: 46 / 84

LINCOLN ELECTRIC

SAE-300® HE Service Manual

SHUNT FIELD CIRCUIT VOLTAGE TEST PROCEDURE

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized

repairs performed on this equipment may result in danger to the technician or machine operator and will

invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety

notes and precautions detailed throughout this manual. If for any reason you do not understand the test

procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department

for electrical troubleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This procedure will determine if the Shunt Field Coils are receiving the necessary power to operate

correctly.

This test should be done if there is little or no output from the welding generator, but auxiliary output is

normal.

MATERIALS NEEDED

Volt/Ohmmeter

Wiring Diagram

TEST PROCEDURE

Turn off the engine on the SAE-300 HE machine.

Locate the 12-pin Molex connector in the wire bundle that exits the welding generator fame. See

Wiring Diagram.

Set the voltmeter for DC voltage and back probe pins #3 and #5, (blue and brown wires) of the 12-

pin Molex connector.

Set the fine current / OCV control to maximum, set the idle switch to “High” and set the

remote/local switch to local position.

Start the engine.

The voltage should read about 123 to 133 Volts DC (Voltage will be a bit higher if machine is not

warmed to normal operating temperature).

If normal DC voltage is present, perform the

Shunt Field Coil Resistance and Ground Test

Procedure

If voltage is not present, check the rheostat, the remote/local switch, the J5 and P10 Molex

connectors. Check all the wiring and terminals connecting the field bridge rectifier, the remote /

local switch, the flashing/flywheel rectifier and the J5 - P10 connectors.

Содержание SAE-300 HE




















































































Результаты поиска

Содержание SAE-300 HE

Отзывы:

Lincoln Electric SAE-300 HE, Руководство по обслуживанию, Страница: 46 / 84

Результаты поиска

Содержание SAE-300 HE

Отзывы: