Lightware 91560001 Скачать руководство пользователя страница 21

Страница: 21 / 126

3. Installation

UMX-HDMI-140 series– User's Manual

Applied firmware package: v1.2.0 | LDC software: v2.4.1b7

3.2.8.

Ethernet Connector (LAN Port)

The extender provides standard RJ45 connectors for TPS IN and LAN ports. Always use high

quality Ethernet cable for connecting transmitters and receivers.

Wiring of TPS and LAN Cables

Lightware recommends the termination of LAN cables on the basis of TIA/EIA T 568 A or TIA/EIA T 568 B

standards.

3.2.9.

RS-232 Connector

The device contains a 3-pole Phoenix connector which is used for RS-232 serial connection.

Pin nr.

Signal

Ground

TX data

RX data

RS-232 connector pin assignments

Compatible Plug Type

Phoenix

Combicon series (3.5mm pitch, 3-pole), type: MC 1.5/3-ST-3.5.

You can find more information about RS-232 interface in the

Serial Interface

section.

Top

Bottom

Side

3.2.10.

IR Connector

IR detector and IR emitter can be connected to the device with TRS (Tip, Ring, and Sleeve) connectors.

They are also known as (3,5 mm or approx. 1/8”) audio jack, phone jack, phone plug, and mini-jack

plug. The pin assignments are the following for the detector and the emitter:

Detector – 3-pole-TRS

Emitter – 2-pole-TS

1 Tip

Signal (active low)

1 Tip

+5V

2 Ring

GND

2 Ring

Signal (active low)

3 Sleeve

+5V

3 Sleeve

INFO:

Ring pole of the emitter is optional. If your IR emitter has three pole-TRS plug, then the Ring and the

Sleeve are the same signal (Output - ).

You can find more information about Infrared interface in the

IR Interface

section.

3.2.11. GPIO - General Purpose Input/Output Ports

UMX-HDMI-140 series switchers contain a 8-pole Phoenix connector with seven GPIO pins, which operates at

TTL digital signal levels and can be set to high or low level (Push-Pull). The direction of the pins can be input or

output (adjustable). Voltage ranges for GPIO inputs are the following:

Input voltage [V]

Output voltage [V]

Max. current [mA]

Logical low level

0 - 0.8

0 - 0.5

Logical high level

2 - 5

4.5 - 5

INFO:

The maximum total current for the seven GPIO pins is 180 mA.

Pin nr.

Level and

direction

Configur

able

2
3
4
5
6
7

Ground

GPIO connector and plug pin assignments

Compatible plug type

Phoenix

Combicon series (3.5mm pitch 8-pole), type: MC 1.5/8-ST-3.5.

You can find more information about GPIO interface in the

GPIO Interface

section.



 



Содержание 91560001































































































































Результаты поиска

Содержание 91560001

Отзывы:

Похожие инструкции для 91560001

Бренды по названию

Популярные бренды

Lightware 91560001, Руководство пользователя

Результаты поиска

Содержание 91560001

Отзывы:

Похожие инструкции для 91560001

Бренды по названию

Популярные бренды