LG UM36FH Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 71

background image

53

THE INDOOR UNIT INSTALLATION

ENGLISH

Pump Down

This is performed when the unit is relocated
or the refrigerant circuit is serviced.

Pump Down means collecting all refrigerant into
the outdoor unit without the loss of refrigerant.

NOTE

Be sure to perform Pump Down procedure
in the cooling mode.

Pump Down Procedure

- Connect a low-pressure gauge manifold

hose to the charge port on the gas side
service valve.

- Open the gas side service valve halfway and

purge the air in the manifold hose using the
refrigerant.

- Close the liquid side service valve(all the

way).

- Turn on the unit's operating switch and start

the cooling operation.

- When the low-pressure gauge reading

becomes 1 to 0.5 kg/cm

2

G(14.2 to 7.1

P.S.I.G.), fully close the gas side valve and
then quickly turn off the unit. Now Pump
Down procedure is completed, and all
refrigerant is collected into the outdoor unit.

WARNING

!

It may cause explosion or injury.

After pump down, power must be turned
off before removing the pipe. When
operating this product without connecting
the pipe, there will be high pressure inside
the compressor due to the entry of air,
possibly causing explosion or injury.

Test operation

- If you press and hold the On/Off button for

3 – 5 seconds instead of 6 seconds, the unit
will switch to the test operation.

- In the test operation, the unit blows out

strong air for cooling for 18 minutes and then
returns to the factory default settings.

NOTE

If the actual pressure is higher than shown,
the system is most likely over-charged, and
charge should be removed. If the actual
pressure are lower than shown, the system
is most likely undercharged, and charge
should be added.

«
...
51
52
53
54
55
...
»

Содержание UM36FH








































































Отзывы:

Нет отзывов

Похожие инструкции для UM36FH

Бренд: Waeco Страницы: 29

Бренд: Waeco Страницы: 22

Бренд: Gree Страницы: 28

Бренд: Hyundai Страницы: 52

Бренд: Daikin Страницы: 20

Бренд: Daewoo Страницы: 60

Бренд: Sinclair Страницы: 31

Continuous dry verge

Бренд: Sandtoft Страницы: 2

TherapyAir iOn PWC-570

Бренд: Zepter Страницы: 17

Бренд: IDEAL Страницы: 65

Бренд: Airwell Страницы: 94

Бренд: Venmar Страницы: 20

Бренд: Airpura Страницы: 16

Бренд: Essick Страницы: 4

Бренд: Perfect Aire Страницы: 20

Comfora FTXP20~71L2V1B

Бренд: Daikin Страницы: 68

Comfora XP Series

Бренд: Daikin Страницы: 172

Бренд: Daikin Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды