LG UM36FH Скачать руководство пользователя страница 6

Страница: 6 / 71

SAFETY INSTRUCTIONS

ENGLISH

• Compliance with national gas regulations shall be observed.
• Ducts connected to an appliance shall not contain an ignition

source. (for R32)

Installation

• Always perform grounding.

- Otherwise, it may cause electrical shock.

• Don’t use a power cord, a plug or a loose socket which is

damaged.
- Otherwise, it may cause a fire or electrical shock.

• For installation of the product, always contact the service center or

a professional installation agency.
- Otherwise, it may cause a fire, electrical shock, explosion or injury.

• Securely attach the electrical part cover to the indoor unit and the

service panel to the outdoor unit.
- If the electrical part cover of the indoor unit and the service panel

of the outdoor unit are not attached securely, it could result in a
fire or electric shock due to dust, water, etc.

• Always install an air leakage breaker and a dedicated switching board.

- No installation may cause a fire and electrical shock.

• Do not keep or use flammable gases or combustibles near the air

conditioner.
- Otherwise, it may cause a fire or the failure of product.

• Ensure that an installation frame of the outdoor unit is not

damaged due to use for a long time.
- It may cause injury or an accident.

• Do not disassemble or repair the product randomly.

- It will cause a fire or electrical shock.

• Do not install the product at a place that there is concern of falling

down.
- Otherwise, it may result in personal injury.

• Use caution when unpacking and installing.

- Sharp edges may cause injury.

• The appliance shall be stored in a room without continuously

operating open flames (for example an operating gas appliance)
and ignition sources (for example an operating electric heater).

Содержание UM36FH








































































Результаты поиска

Содержание UM36FH

Отзывы:

Похожие инструкции для UM36FH

Бренды по названию

Популярные бренды

LG UM36FH, Инструкция по эксплуатации

Результаты поиска

Содержание UM36FH

Отзывы:

Похожие инструкции для UM36FH

Бренды по названию

Популярные бренды