LG UM36FH Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 71

background image

60

INSTALLATION OF DECORATIVE PANEL(ACCESSORY)

ENGLISH

Air conditioner
unit

Decorative panel

Fit the insulator (this part) and
be careful for cool air leakage

Good example

Ceiling

board

Ceiling

board

Decorative
panel

Air

Cool air leakage

(no good)

Bad example

Air conditioner unit

CAUTION

!

Install certainly the decorative panel.
Cool air leakage causes sweating.

⇨

Water drops fall.

PRECAUTIONS IN TEST RUN

- The initial power supply must provide at least

90 % of the rated voltage.
Otherwise, the air conditioner should not be
operated.

- To cancel the test run, press any button.

CAUTION

!

• For test run, carry out the cooling

operation firstly even during heating
season. If heating operation is carried
out firstly, it leads to the trouble of
compressor. Then attention must be
paid.

• Carry out the test run more than 5

minutes without fail.
(Test run will be cancelled 18 minutes
later automatically)

CHECK THE FOLLOWING ITEMS WHEN
INSTALLATION IS COMPLETED

- After completing work, be sure to measure and

record trial run properties, and store measured
data, etc.

- Measuring items are room temperature,

outside temperature, suction temperature,
blow out temperature, wind velocity, wind
volume, voltage, current, presence of abnormal
vibration and noise, operating pressure, piping
temperature, compressive pressure.

- As to the structure and appearance, check

following items.

* Is the circulation of air adequate?
* Is the draining smooth?
* Is the heat insulation complete

(refrigerant and drain piping)?

* Is there any leakage of refrigerant?
* Is the remote controller switch operated?
* Is there any faulty wiring?
* Are not terminal screws loosened?

M4......118 N.cm{12 kgf.cm}
M5......196 N.cm{20 kgf.cm}
M6......245 N.cm{25 kgf.cm}
M8......588 N.cm{60 kgf.cm}

Connection of power supply

- Connect the power supply cord to the

independent power supply.
Circuit breaker is required.

- Operate the unit for 15 minutes or more.

Evaluation of the performance

- Measure the temperature of the intake and

discharge air.

- Ensure the difference between the intake

temperature and the discharge one is more
than 8 °C (Cooling) or reversely (Heating).

Thermometer

«
...
58
59
60
61
62
...
»

Содержание UM36FH








































































Отзывы:

Нет отзывов

Похожие инструкции для UM36FH

Бренд: acerpure Страницы: 48

SUNLINE MAGNUM DJ 180

Бренд: York Страницы: 40

641415.30 series

Бренд: Dometic Страницы: 18

Бренд: Sinclair Страницы: 38

Depuro Plus 230

Бренд: Vortice Страницы: 72

Бренд: Daikin Страницы: 44

Бренд: Click Страницы: 16

Бренд: York Страницы: 186

Бренд: TCL Страницы: 27

Бренд: turbionaire Страницы: 50

Бренд: U.S. Products Страницы: 12

Бренд: Daikin Страницы: 44

Бренд: Daikin Страницы: 34

Бренд: Haier Страницы: 100

AtmosAir Everest

Бренд: Clean Air Страницы: 15

FreshAir Focus A1007D

Бренд: vollara Страницы: 4

Бренд: GE Страницы: 10

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды