LG ARWN038GA2 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 81

LG ARWN038GA2 Скачать руководство пользователя страница 7

- 7 -

Copyright ©2013 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

Safety Precautions

Use power cables of sufficient current
carrying capacity and rating.

• Cables that are too small may leak, generate

heat, and cause a fire.

Do not use the product for special purposes,
such as preserving foods, works of art, etc. It
is a consumer air conditioner, not a precision
refrigeration system.

• There is risk of damage or loss of property.

When installting the unit in a hospital, com-
munication station, or similar place, provide
sufficient protection against noise.

• The inverter equipment, private power generator,

high-frequency medical equipment, or radio com-
munication equipment may cause the air condition-
er to operate erroneously, or fail to operate. On the
other hand, the air conditioner may affect such
equipment by creating noise that disturbs medical
treatment or image broadcasting.

Do not install the product where it is exposed
to sea wind (salt spray) directly.

• It may cause corrosion on the product.

Corrosion, particularly on the condenser and
evaporator fins, could cause product malfunction
or inefficient operation.

■

Operation

Do not use the air conditioner in special
environments.

• Oil, steam, sulfuric smoke, etc. can significantly

reduce the performance of the air conditioner or
damage its parts.

Do not block the inlet or outlet.

• It may cause failure of appliance or accident.

«
...
5
6
7
8
9
...
»

Содержание ARWN038GA2


















































































Отзывы:

Нет отзывов