LG ARWN038GA2 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 81

LG ARWN038GA2 Скачать руководство пользователя страница 15

- 15 -

Copyright ©2013 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

Function

1. Basic control ...................................................................................................................16

1.1 Normal operation .......................................................................................................16
1.2 Compressor control....................................................................................................16
1.3 Master and slave unit's EEV control ..........................................................................17

2. Special control ................................................................................................................18

2.1 Oil return control ........................................................................................................18
2.2 Stopping operation .....................................................................................................20

3. Protection control ...........................................................................................................21

3.1 Pressure protection control ........................................................................................21
3.2 Discharge temperature control...................................................................................22
3.3 Inverter protection control ..........................................................................................22
3.4 Liquid back control .....................................................................................................23
3.5 Pressure switch..........................................................................................................23

4. Other control ...................................................................................................................24

4.1 Initial setup .................................................................................................................24
4.2 Vacuum Mode ............................................................................................................26
4.3 Black Box Function ....................................................................................................27

Function

«
...
13
14
15
16
17
...
»

Содержание ARWN038GA2


















































































Отзывы:

Нет отзывов