Error code
Description
Action
940
RIP to engine communication failure.
See
“Engine error service check” on page 165
.
941
Engine card failure.
948
Engine card—Pel clock check failed.
949
Engine card—Delay line calibration
failure.
950
Non-Generic FRU installed.
Mismatch between system NVRAM
part and mirror NVRAM part.
Note:
.xx
points to the setting that
does not match.
952
A recoverable NVRAM cyclic
redundancy check error occurred.
Notes:
•
n
is the offset at which the error
occurred.
•
Performing a POR will clear this
error.
953
NVRAM chip failure with mirror part.
954
NVRAM chip failure with system part.
955
The NAND flash failed the cyclic
redundancy check or the NAND
experienced an uncorrectable multi-
bit failure.
Note:
<LOC>
indicates the source of
the failure.
956
RIP card failure—Processor failure.
957
RIP card failure—ASIC failure.
958
Controller board NAND failure.
959
Invalid firmware—Service system
board.
960
RAM memory error—RAM soldered on
the card is bad.
961
RAM memory error—RAM in slot 1 is
bad.
962
RAM memory error—RAM in slot 2 is
bad.
963
RAM memory error—RAM in slot 3 is
bad.
964
Download emulation cyclic
redundancy check error—Checksum
failure detected in the emulation
header or emulation file.
3400-48x
Diagnostics and troubleshooting
159
Содержание MB2236
