Lenze POWERLINK E84DGDV Series Скачать руководство пользователя страница 44

Страница: 44 / 70

Error messages

Possible causes and remedies

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

EPL: Invalid module configuration [0x01bc6430]

EPL: State OPERATIONAL lost [0x01bc8131]

EPL: Invalid address selected [0x01bc8261]

EPL: Synchronisation lost from MN [0x01bc8265]

EPL: Telegram error detected (CRC) [0x01bc8266]

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Module configuration is faulty.

Check and correct module configuration.

Response

(Lenze setting printed in bold)

Setting:

C13880/1



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

Data exchange via POWERLINK has been terminated.

• Also see the chapter "

Interruption of POWERLINK

• Check the network cable (plug) and replace it if

necessary.

• Plug the network cable into the POWERLINK terminal

X251 or X252 and continue to check the status of the

managing node.

Response

(Lenze setting printed in bold)

Setting:

not possible



No reaction



System fault



Fault



Trouble



Quick stop by trouble



WarningLocked



Warning



Information

Cause

Remedy

An invalid IP address has been assigned by the managing

node via POWERLINK or set as node ID.

• Ensure that a valid IP address is assigned by the

managing node via POWERLINK.

• Set valid node ID.



Node address (node ID) setting (



26)

Response

(Lenze setting printed in bold)

Setting:

C13880/2



None



System fault



Fault



Trouble



Quick stop by trouble



Warning locked



Warning



Information

Cause

Remedy

In the controlled node, the synchronisation cycle of the

managing node has failed. The controlled node changes

automatically to the NMT_CS_PREOPERATIONAL_1

state and waits for a new run-up by the managing node.

• Check network cable and components (failure of

managing node, router).

• Restart managing node if required.

Response

(Lenze setting printed in bold)

Setting:

C13880/3



None



System fault



Fault



Trouble



Quick stop by trouble



Warning locked



Warning



Information

Cause

Remedy

Faulty telegrams (CRC error) have been detected.

Possible causes:

• A device in the network is not EPL-compliant.

• EMC interference is too strong.

• Check if a non-EPL-compliant device is in the network

(e.g. diagnostics PC).

• Reduce EMC interference on the network or use an

additional shield connection.

Содержание POWERLINK E84DGDV Series







































































Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды

Lenze POWERLINK E84DGDV Series, Руководство по связи

Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды