Lenze POWERLINK E84DGDV Series Скачать руководство пользователя страница 26

Страница: 26 / 70

Commissioning

Node address (node ID) setting

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.2

Node address (node ID) setting

The POWERLINK node address (node ID) can either be defined via the DIP switches of the Drive Unit

or set in the »EASY Starter«/»Engineer« in code

C13899

• If you set the node via DIP switches, the Drive Unit cannot be configured anymore via the DIP

switches DIP1, DIP2 and the potentiometers P1, P2, P3.

• In case of the following DIP switch settings, the node ID is obtained from

C13899

• DIP1, switch 1 is "ON"
• DIP1, switch 1 is "OFF" and DIP2, switch 1 ... 8 are "OFF" (Lenze setting).

• The node IDs must differ from each other in case of several networked POWERLINK nodes.
• Save the changed parameter settings with the device command

C00002/11

(save all parameter

sets).

DIP switches of the Drive Unit



Note!

• The DIP switches can only be accessed when the drive unit is detached from the

communication unit. Loosen the four fixing screws at the drive unit.

Observe the

notes in the mounting instructions.

• Switch off the voltage supply of the controller and the external supply of the

communication unit before starting with the disassembly of the drive unit.

• The DIP switches are only read in when the device is switched on.

DIP switches of the Drive Unit 0.37 ... 3 kW

DIP1

DIP switches for configuring the Drive Unit or for setting the POWERLINK node address

DIP2

Содержание POWERLINK E84DGDV Series







































































Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды

Lenze POWERLINK E84DGDV Series, Руководство по связи

Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды