Lenze POWERLINK E84DGDV Series Скачать руководство пользователя страница 27

Страница: 27 / 70

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

Commissioning

Node address (node ID) setting

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Setting of the DIP switches DIP1 and DIP2

• The valid address range is 0 ... 239. If the value set via DIP switch DIP2 is higher than 239, the

node ID is set to 239.

• The node ID is used in the last byte of the IP address: 192.168.100.[

Node ID

]

• In

C13920

, the DIP switch position of DIP2 (node ID) of the last mains switching is displayed.

• In

C13864

, the active node ID is displayed.

•

C13865

displays whether the node ID has been set via DIP switches or via

C13899

DIP switches of the Drive Unit 4 ... 7.5 kW

DIP1

DIP switches for configuring the Drive Unit or for setting the POWERLINK node address

DIP2

DIP1

Description

OFF

...

The node ID 1 ...239 can be set via DIP2.

(Lenze setting)

...

Obtain node ID from

C13899

DIP2

Description

Value

128

OFF

OFF Obtain node ID from

C13899

(Lenze setting)

OFF

Node ID = 1

...

OFF

Node ID = 239

If the set value is higher than 239, the node

ID is set to 239.

Содержание POWERLINK E84DGDV Series







































































Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды

Lenze POWERLINK E84DGDV Series, Руководство по связи

Результаты поиска

Содержание POWERLINK E84DGDV Series

Отзывы:

Похожие инструкции для POWERLINK E84DGDV Series

Бренды по названию

Популярные бренды