Lenovo ThinkCentre Edge 3484 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 170

background image

6. Connect one end of the signal cable to the rear of the new optical drive and the other end to an available

SATA connector on the system board. See “Locating parts on the system board” on page 72. Then,
locate an available five-wire power connector and connect it to the rear of the new optical drive.

Figure 24. Connecting the optical drive

7. To complete the installation or replacement, go to “Completing the parts replacement” on page 112.

Replacing the heat sink and fan assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

ThinkCentre User Guide

. To obtain a copy of the

ThinkCentre User Guide

, go to:

http://www.lenovo.com/ThinkCentreUserGuides

This section provides instructions on how to replace the heat sink and fan assembly.

CAUTION:

The heat sink and fan assembly might be very hot. Turn off the computer and wait three to five
minutes to let the computer cool before removing the computer cover.

To replace the heat sink and fan assembly, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 82.

3. Lay the computer on its side for easier access to the system board.

4. Locate the heat sink and fan assembly. See “Locating major FRUs and CRUs” on page 69.

5. Disconnect the heat sink and fan assembly cable from the microprocessor fan connector on the system

board. See “Locating parts on the system board” on page 72.

92

ThinkCentre Hardware Maintenance Manual

«
...
94
95
96
97
98
...
»

Содержание ThinkCentre Edge 3484











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkCentre Edge 3484

Бренд: ACE COMPUTERS Страницы: 37

Desktop Hardware

Бренд: Digiop Страницы: 2

Бренд: WAGO Страницы: 52

Бренд: IBM Страницы: 155

Бренд: WinSystems Страницы: 53

Бренд: Sun Microsystems Страницы: 45

Бренд: HP Страницы: 53

Бренд: Honeywell Страницы: 100

OptiPlex 7440 All-In-One W11C

Бренд: Dell Страницы: 80

Бренд: Dell Страницы: 41

Бренд: Dell Страницы: 38

Бренд: Dell Страницы: 61

Бренд: Dell Страницы: 70

Бренд: Dell Страницы: 208

Precision 8F765

Бренд: Dell Страницы: 260

Precision 8F764

Бренд: Dell Страницы: 152

Precision M2800

Бренд: Dell Страницы: 81

Бренд: Dell Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды