Lenovo ThinkCentre Edge 3484 Скачать руководство пользователя страница 130

Страница: 130 / 170

This section provides instructions on how to install or replace the optical drive.

Note:

The optical drive is only available in some models.

To replace an optical drive, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 116.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 117.

4. Pivot the drive bay assembly upward. See “Accessing the system board components and drives” on

page 118

5. Disconnect the signal cable and the power cable from the optical drive.

6. Hold the optical drive and remove the two screws that secure the optical drive.

Figure 65. Removing the optical drive

126

ThinkCentre Hardware Maintenance Manual

Содержание ThinkCentre Edge 3484











































































































































































Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды

Lenovo ThinkCentre Edge 3484, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды