Lenovo ThinkCentre Edge 3484 Скачать руководство пользователя страница 150

Страница: 150 / 170

5. Grasp the WiFi adapter card that is currently installed and gently pull it out of the slot.

Figure 87. Removing the WiFi adapter card

Note:

The card fits tightly into the card slot. If necessary, alternate moving each side of the card a

small amount until it is removed from the card slot.

Removing the WiFi card module

To remove the WiFi card module, do the following:

1. Remove the WiFi adapter card from the computer, and then disconnect the front and rear WiFi antenna

cables from the WiFi card module.

Figure 88. Removing the WiFi antenna cables

146

ThinkCentre Hardware Maintenance Manual

Содержание ThinkCentre Edge 3484











































































































































































Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды

Lenovo ThinkCentre Edge 3484, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды