Lenovo ThinkCentre Edge 3484 Скачать руководство пользователя страница 137

Страница: 137 / 170

10. Lower and position the heat sink fan duct on the top of the heat sink and fan assembly until it snaps

into position.

Figure 74. Installing the heat sink fan duct

11. Secure the power supply assembly cables with the cable clips and ties in the chassis.

12. To complete the installation or replacement, go to “Completing the parts replacement” on page 154.

Replacing the heat sink and fan assembly

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

ThinkCentre User Guide

. To obtain a copy of the

ThinkCentre User Guide

, go to:

http://www.lenovo.com/ThinkCentreUserGuides

This section provides instructions on how to replace the heat sink and fan assembly.

CAUTION:

The heat sink and fan assembly might be very hot. Turn off the computer and wait three to five
minutes to let the computer cool before removing the computer cover.

To replace the heat sink and fan assembly, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 116.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 117.

Chapter 10

Replacing FRUs (Machine Types: 3493, 3496, and 3497)

133

Содержание ThinkCentre Edge 3484











































































































































































Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды

Lenovo ThinkCentre Edge 3484, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды