Lenovo ThinkCentre Edge 3484 Скачать руководство пользователя страница 87

Страница: 87 / 170

Removing and reinstalling the front bezel

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
in the

ThinkCentre User Guide

. To obtain a copy of the

ThinkCentre User Guide

, go to:

http://www.lenovo.com/ThinkCentreUserGuides

This section provides instructions on how to remove and reinstall the front bezel.

To remove and reinstall the front bezel, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 82.

3. Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the front bezel

outward.

Figure 12. Removing the front bezel

Chapter 9

Replacing FRUs (Machine Types: 3484, 3485, and 3492)

Содержание ThinkCentre Edge 3484











































































































































































Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды

Lenovo ThinkCentre Edge 3484, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды