Lenovo ThinkCentre Edge 3484 Скачать руководство пользователя страница 153

Страница: 153 / 170

3. Locate the two PCI Express x1 slots on the system board. See “Locating parts on the system board”

on page 79.

4. Install the WiFi adapter card into one of the two PCI Express x1 slots. Then install the screw to secure

the WiFi adapter card in place.

Figure 93. Installing the WiFi adapter card

5. If the installed WiFi card module supports the Bluetooth function, use a Bluetooth cable to connect the

Bluetooth connector on the WiFi adapter card to the front USB connector on the system board.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 154.

Installing or removing the rear WiFi antenna

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
on page 1.

This section provides instructions on how to install or remove the rear WiFi antenna.

Installing the rear WiFi antenna

To install the rear WiFi antenna, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Install the rear WiFi antenna to the rear WiFi antenna cable connector attached on the rear of the

computer.

Chapter 10

Replacing FRUs (Machine Types: 3493, 3496, and 3497)

149

Содержание ThinkCentre Edge 3484











































































































































































Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды

Lenovo ThinkCentre Edge 3484, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды