Lenovo ThinkCentre Edge 3484 Скачать руководство пользователя страница 156

Страница: 156 / 170

5. Stick the front antenna to the front panel as shown. Then insert the front antenna cable through the

hole in the front panel.

Figure 97. Installing the front WiFi antenna

6. Connect the front antenna cable to the WiFi card module.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 154.

Removing the front WiFi antenna

To remove the front WiFi antenna, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 116.

3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 117.

4. Disconnect the front antenna cable from the WiFi card module.

152

ThinkCentre Hardware Maintenance Manual

Содержание ThinkCentre Edge 3484











































































































































































Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды

Lenovo ThinkCentre Edge 3484, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание ThinkCentre Edge 3484

Отзывы:

Похожие инструкции для ThinkCentre Edge 3484

Бренды по названию

Популярные бренды