__p
DS67U Quick Guide【 English 】
53R-DS67U3-H001
C. Component Installation
D. Complete
3. Lay the HDD or SSD into its drive bay and push it gently to the right
until it clicks into place.
1. Replace the covers and refasten the screws.
3. Complete.
A. Begin Installation
1. Unscrew two screws of the chassis cover.
For safety reasons, please ensure that the power cord is discon-
nected before opening the case.
1
2
2. Slide the cover forwards and upwards.
4. Refasten screws.
Left / Right Panel
Back Panel
Front Panel
F1. USB 3.0 Ports x2
F2. USB 2.0 Ports x2
F3. Power LED
F4. HDD LED
F5. Power Button
F6. COM 1 :
Support RS232/RS422/RS485
F7. COM 2 :
Support RS232
F8. SD Card Reader
B. Memory Module Installation
notch
Supports DDR3L SO-DIMM
(1.35V)
1. Locate the SO-DIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
mechanism.
5. Repeat above steps to install additional memory modules, if required.
2. Place the HDD or SSD in the rack and secure with the two screws from
the side.
1. Unscrew the rack from chassis.
Motherboard Illustration Back
Jumper Settings
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle.
Dispose of used batteries according to the manufacturer's instructions.
Kensington
®
Lock
Kensington
®
Lock
45-degree
angle
1
2
3
Latch
Latch
SD Card Reader FFC
Connector - CON3
Intel
®
Celeron
®
/ Core
™
i series
processor
Motherboard Illustration Front
This mainboard does only support 1.35V DDR3L memory
modules.
B1.
External Power & Clear CMOS
(Pin definition )
B2. DisplayPort
B3. HDMI Port
B4. MIC-in Jack
B5. Headphone Jack
B6. USB 2.0 Ports x2
B7. LAN Ports x2
B8. DC IN
B9. Connectors for WLAN antennas
J4
USB 2.0 Ports x2
J1
J2
COM Port 1
LAN Ports x2
USB 2.0 Ports x2
Headphone JACK
MIC-in JACK
HDMI Port
DisplayPort
COM1 & COM2
Power Switch - JP1
Power Button - SW3
M.2 2242 M Key Slots
External Power SW &
Clear CMOS - SW2
RTC Battery Connector - BAT1
HDD LED
Power LED
DC IN
COM Port 2
J3
2.5 inch HDD Slot
DDR3L SO-DIMM Slots
AC Back Auto Power ON
(DEFAULT =>Disable,
short 1-2) - JP9
J4
L
The product’s colour and specifications may vary from the actually shipping product.
F3
F4
F5
F6
F8
F7
F1
F2
M.2 2230 E Key Slots
USB 3.0 Ports x2
2.
Screw the included antennas onto the appropriate connectors at the back panel (B9).
Make sure they are aligned vertically or horizontally to achieve the best possible
signal reception.
5. As shown, unfasten the screw first.
6. Install the M.2 device into the M.2 slot and secure with the screw.
Debug Header
Please press the "Del" key while booting to enter BIOS.
Here, please load the optimised BIOS settings.
Operation Position:
Please make sure to use either the supplied feet or the VESA mount.
Make sure all antennas are aligned in the correct direction.
J1
COM Port 1
RS-232, RS-422, RS-485 switch by BIOS setting
1 2 3 4 5
6 7 8 9
COM1 (RS232)
Pin Signal Name
Pin Signal Name
1
DCD
2 RX
3
TX
4 DTR
5
GND
6 DSR
7
RTS
8 CTS
9
RI-
COM1 (RS422)
Pin Signal Name Pin Signal Name
1
TXD-
2
TXD+
3
RXD-
4
RXD+
5
GND
6
---
7
---
8
---
9
---
COM1 (RS485)
Pin Signal Name
Pin Signal Name
1
Data-
2 Data+
3
---
4 ---
5
GND
6 ---
7
---
8 ---
9
---
COM1 & COM2 Power Switch
1
3
5 7 9
2
4
6 8 10
J2
JP1
COM1 (pin9)
COM2 (pin9)
Short Pin
Function
Short Pin
Function
1-2 (Default) RI1
3-4 (Default)
RI2
5-7
+5V
6-8
+5V
7-9
+12V
8-10
+12V
AC Back Auto Power ON
1
2
J3
JP9
Pin
AC Back auto Power ON function
Short 1-2
Disable (Default)
Open
Enable
J4
External Power SW & Clear CMOS
1
3
2
4
SW2
Pin Signal Name
1
PWRSW-
2
+5V
3
GND
4
RTC_RST#
62R-DS67U0-5201 DS67U
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
B1
B3
B4
B5
B7
B8
B2
B6
B9
