IOM / Rooftop Smart and Linéa™ Range - Page 59
USING THE T7300 THERMOS
USING THE T7300 THERMOS
USING THE T7300 THERMOS
USING THE T7300 THERMOS
USING THE T7300 THERMOST
T
T
T
TA
A
A
A
AT
T
T
T
T
Set Program
Set Temperature
Change
Time/Temp
Occupied
Temp
Unoccupied
Start Time
Day
System
Fan
Copy
Occupied
Start Time
Run
Program
Temporary
Occupied
Continuous
Unoccupied
Set Current
Day/Time
Clear
Start Time
Unoccupied
Temp
Heat/Cool
Settings
Auto
System
Fan
Mon
Room
AM
Occupied
Heat
2
3
4
5
6
7
8
9
10
11
13
14
15
16
12
1
Figure 70
THERMOSTAT KEY LOCATIONS AND DESCRIPTIONS
1
Enter occupied program mode
2
Enter unoccupied program mode
3
Set current day or program day
4
Set occupied temperature setpoints
5
Set unoccupied temperature setpoints and
scrolls through installer setup and system test
6
Increase temperature or time setting
7
Decrease temperature or time setting
8
Change between heating ans cooling
setpoints and scrolls backwards through ins-
taller setup numbers and system test
9
Select fan operation
10 Select system operation
11 Copy one programmed day to another day
12 Clear program period
13 Set current day and time
14 Enter hold mode
15 Set override temperature offset and activate
temporary override
16 Returns to normal operation
INSTALLER SETUP
NOTE : For most applications, the thermostat factory settings
do not need to be changed.
The Installer Setup is used by the installer to customize the
thermostat to specific systems. Installer Setups are listed in
the below table. The below table includes all the configuration
options available.
A combination of key presses are required to use the Installer
Setup feature.
- To enter the Installer Setup, press and hold the
Heat/Cool
Settings
key and both the increase
and
decrease keys
until the first number is displayed. All display segments
appear for approximately three seconds before the
number is displayed. See figures 71 and 72.
- To advance to the next Installer Setup number, press
the
Unoccupied
Temp
key.
- To return to an Installer Setup number, press the
Heat/Cool
Settings
key.
- To change a setting, use the increase
or
decrease key.
- To exit the Installer Setup, press the
Run
Program
key.
The Installer Setup is automatically exited if no key is
pressed for four minutes.
NOTE : Be sure to set the thermostat time after exiting the
Installer Setup. Installer Setup numbers are listed in below
table.
CAUTION
Possible Equipment Damage.
Fan must be running when system is operating.
Heat pump and electric heat systems must be configured
correctly in Installer Setup 2 to prevent equipment damage
caused by the system running without the fan.
IMPORTANT
Only configurable numbers are shown on the device.
Example : If the thermostat does not have a system key,
Installer Setup number 12 will not be displayed.
Review following table factory settings and mark any desired
changes in the Actual Setting column. When the Installer
Setup is complete, review the settings to confirm that they
match the system.
Heat
Auto
System
Fan
Off
Auto
Un
Mon
Wait
Lo
In
Room
Remote
%Humid
Auto
Sav
AM
PM
Comm
Cool
Duct
Only
On
Recovery
Hi
Med
Cool
TueWedThuFriSatSun
Occupied 12 Override
Aux Ht
Aux Ht
Em Ht
Em Ht
Set Program
Set Program
Set Day/Time
Set Day/Time
Start Time
Temporary Setting Enrg
Em Heat
LED DISPLAY OF ALL SEGMENTS
Figure 71
INSTALLER SETUP NUMBER
AND SETTING DISPLAY
Figure 72
Mode number display
(column 2 in following
table)
Factory setting or other choice
display (column 3 or 5 in
following table)
