11
P
Ure
a
Ir
S
e
qUIPment
P
arameters
The following is a complete list of all possible parameters listed under
System
. Parameters actually available are dependent
on the Lennox communicating equipment type detected and non-communicating equipment added.
From the Dealer Control Center Screen, go to
equipment
>
PureAir
. There you will find the applicable parameter settings
for PureAir
S
.
Table 5.
PureAir S
Parameters
Parameter
Description
Equipment
PureAir Filter
Dirty Filter and UV
Life Detection
Default: ON. Options are either ON or OFF. Alarms 503 and 504 will not be displayed when this parameter is set
to OFF. The diagnostics screen on the thermostat will continue to show values for both filter life and UV lamp life
regardless of the value of this parameter.
•
This parameter turns on and off the filter life and UV lamp life reporting. When set to off, the control will continue to
calculate the remaining filter life through continuous sampling, but will not use filter tests to determine filter life. The
control will:
• Perform a UV lamp calibration upon indication of a lamp change regardless of the value of this parameter.
• Will calculate UV lamp life remaining regardless of the value of this parameter.
Max Air Filtered
between Tests
Default is 100%, Range is 50% to 100% Changes can be made in increments of 10%.
This parameter modifies the amount of air that is allowed to pass through the filter after a valid % life determination
before a filter test is initiated.
This parameter is expressed as a percentage of the cubic feet of air that would pass through the filter if the fan
operated at continuous fan CFM for 30 days.
UV lamp operation
detection
Default: ON. Options are either ON or OFF.
Filter Life
Provides percentage of remaining filter life. This is for display purposes only and cannot be changed.
Last replacement
date for filter
Date last filter reset was accomplished. This is for display purposes only and cannot be changed
Purifier life
Provides percentage of remaining purifier life. This is for display purposes only and cannot be changed
NOTE:
Purifier life is referring to the
UVA Lamp / PCO cartridge insert.
Last replacement date
for purifier insert
Date last purifier insert reset was accomplished. This is for display purposes only and cannot be changed
• reset
PureAir
S
will reset all
PureAir
S
parameters back to factory defaults.
•
reset purifier insert will reset (
recalibration
) it to 100%. This is usually accomplished after the UVA Lamp / PCO cartridge insert has been replaced.
•
reset filter will reset (
recalibration
) it to 100%. This is usually accomplished after the air filter has been replaced.
n
otIfIcatIons
(a
lert
c
odes
)
The thermostat’s notification screens provide information
on active notifications and previously cleared notifications.
When selecting either a cleared or active notification a brief
description and alert code will be displayed. Notifications are
categorized by system, indoor unit (air handler or furnace),
outdoor unit (air conditioner or heat pump), zoning control (if
installed) and thermostat.
t
ests
and
d
IagnostIcs
f
UnctIon
There are no installer tests or diagnostic features available
for the
PureAir
S
accessory.
I
nstallatIon
r
ePort
PureAir
S
accessory information includes equipment name,
model number, serial number and firmware version.
In addition, when selecting
PureAir
S
, filter life, last
replacement date for filter and purifier life and last
replacement date for purifier information is available.
System
Air Conditioner
PureAir S
Air Handler
installation report
model number
software version
serial number
PCO3S14-16
123456
00.03.0400
name
Equipment Name
PureAir Filter
Dirty Filter Detection and UV life Detection
On
Max Air Filtered between Tests
100.0%
UV lamp operatoin detection
Filter life
100%
Installation date for filter
3/1/2018
PureAir S
On
3/02/2018
overview
Figure 18. Installation Report
