Leica EM ACE600 Скачать руководство пользователя страница 116

Страница: 116 / 132

Operating Manual Leica EM ACE600

Version 01/19

Page 111

5.1.1 Source cover

If the source cover closes too quickly, it is possible to tighten the hinges using a 3
mm Allen key. Be careful not to over tighten.

5.2

Cleaning of the Leica EM ACE600

The internal shielding, shutter including the glow discharge electrode and the
anode ring should be cleaned or replaced when:



Peeling or thick coating is visible



If contamination is observed during EM imaging



Pumping time to reach base vacuum increases significantly

All coating sourced should be cleaned as as soon as there is:



Clearly seen a thicker film of coating on the source



The risk that material could peel off



Latest when material starts to peel off

Thin threads can peel off the anode ring and cause a short circuit.

Recommendation
Usually, only the glass door needs to be cleaned, depending on the layer
thicknesses coated and the visibility needs. The chamber shielding, especially
when always using the same material, does not need to be cleaned very often.

Содержание EM ACE600





































































































































Результаты поиска

Содержание EM ACE600

Отзывы:

Похожие инструкции для EM ACE600

Бренды по названию

Популярные бренды

Leica EM ACE600, Руководство по эксплуатации

Результаты поиска

Содержание EM ACE600

Отзывы:

Похожие инструкции для EM ACE600

Бренды по названию

Популярные бренды