Leica EM ACE600 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 132

background image

Operating Manual Leica EM ACE600

Version 01/19

Page 45

4.3

Vacuum test

After connecting the coater as described in 3.5, the coater can be tested for
vacuum.

Switch on the instrument on the rear by pushing the mains switch down and push
the Pump button.

If the vacuum does not reach 100

mbar in 5 min, a vacuum leak is present

and needs to be eliminated.

4.4

Process start and stop

The coating process can be started at any time (system evacuated or not) if the
door and source cover are closed and the source is connected (electronic safety
switches prohibit starting with open door or source cover).

The

button will turn into a

button when the system starts the

coating cycle.

Once the “Start” button is activated, the coater will automatically run the complete
coating cycle. At the end of the process the system eithers stays under vacuum or
vents automatically (vent after process is activated, defined within the process
parameters).

Pressing the “Stop” button will terminate the process (after confirmation)
regardless of the step of the process. The system either stays under vacuum or
vents automatically (vent after process is activated, defined within the process
parameters)

4.5

Thickness monitoring and geometrical correction (QSG)

A quartz crystal swings in a certain frequency. Coated with a material, this
frequency reduces according to the material and the applied thickness. With this
information, the accurate film thickness coated during a process run can be
determined.
Every Leica EM ACE600 system is equipped with the QSG film thickness
measurement monitor. The user can choose between termination by QSG and

«
...
48
49
50
51
52
...
»

Содержание EM ACE600





































































































































Отзывы:

Нет отзывов

Похожие инструкции для EM ACE600

Бренд: NARGESA Страницы: 33

Бренд: Parker Страницы: 54

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: LAZBOY Страницы: 9

Бренд: M-Audio Страницы: 3

Бренд: Zero 88 Страницы: 12

Бренд: Zest4Leisure Страницы: 4

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

Бренд: Abbott Страницы: 64

Бренд: Gako Страницы: 22

Бренд: ABB Страницы: 38

Бренд: olympia electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды