Leica BIOSYSTEMS HistoCore BIOCUT Скачать руководство пользователя страница 77

Страница: 77 / 90

HistoCore BIOCUT

Troubleshooting

Problem

Possible cause

Corrective action

"Stripes" in sections

For the two-in-one blade holder

• Paraffin accumulated on the

rear side of the blade and the

rear pressure plate of the knife

holder.

• Retraction is not selected.

• The clearance angle is too

steep, as close to zero degree.

• The blade has nicks in the

cutting edge.

• Remove paraffin from these

areas regularly.

• Activate the retraction

function.

• Adjust the clearance angle.

• Exchange the blade.

Noises during sectioning

The knife "sings" when

sectioning hard specimens. The

sections show scratches or

chatter marks.

• The sectioning speed is too

fast.

• The clearance angle is too

wide.

• Insufficient clamping of

specimen and/or knife holder.

• Retraction is switched off

during sectioning of resin /

plastic embedded specimens.

• Turn the handwheel at a

slower speed.

• Systematically decrease

the clearance angle until

the optimum adjustment is

obtained.

• Check all screw and clamp

connections on the specimen

holder system and the knife

holder. If necessary, tighten

the levers and screws.

• Switch on retraction.

High blade consumption

• Too great of a sectioning force

was applied.

• Too sharp clearance angle.

• Adjust the sectioning speed

and/or section thickness when

trimming. Select a smaller

section thickness, rotate the

handwheel more slowly.

• Adjust the clearance angle.

7.2

Instrument malfunctions

Problem

Possible cause

Corrective action

There is no further feed motion

and thus no sectioning.

• The front end position has

been reached.

• Run the specimen back by

turning the coarse feed wheel.

Содержание HistoCore BIOCUT



























































































Результаты поиска

Содержание HistoCore BIOCUT

Отзывы:

Бренды по названию

Популярные бренды

Leica BIOSYSTEMS HistoCore BIOCUT, Инструкция по эксплуатации

Результаты поиска

Содержание HistoCore BIOCUT

Отзывы:

Бренды по названию

Популярные бренды