Lehman Renegade 2009 Скачать руководство пользователя страница 5

Страница: 5 / 42

2009-2013

FLH

RENEGADE

General Safety Information

This kit is designed to be installed by a competent technician. Improper installation can affect

the safe operation of your trike, which could also result in serious injury or death. Make sure

you have a complete understanding of the work to be preformed. Unqualified installers are

urged to have the unit installed by a trained technician.

•

Always protect yourself when the vehicle is in the air. Make sure the vehicle is properly supported
anytime you use a hoist or jack.

•

Always use the proper tools.

•

Protect your eyes by using proper safety glasses or goggles.

•

Read through the installation instructions before you begin. Make sure you have all the proper
tools, parts and skill set to perform the installation safely and completely.

NOTE: Compliance with national (DOT-USA, MOT-Canada), State, Provincial, and local vehicle is

standards is the responsibility of the installer. Installation of the parking brake and grab han-

dles is necessary to achieve compliance with DOT/MOT.

ARB Label Confirmation– California Kits

See Fig. 1.

California Air Resource Board (ARB) certification label must be affixed on all swin-

garms for kits sold into California.

2. Label should be placed on left side of swingarm 1/2” from rear

weld.

3. Make sure label correlates with correct model year.

GENERAL INFORMATION

Fig. 1

Содержание Renegade 2009











































Результаты поиска

Содержание Renegade 2009

Отзывы:

Похожие инструкции для Renegade 2009

Бренды по названию

Популярные бренды

Lehman Renegade 2009, Руководство по установке

Результаты поиска

Содержание Renegade 2009

Отзывы:

Похожие инструкции для Renegade 2009

Бренды по названию

Популярные бренды