background image

Power Foundations Owners Manual 99300787-k

3

important information

READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT

This Power Foundation has been quality engineered with design features to assure comfort and 
safety when operated properly.

ELEctRicAL gROUNdiNg
This product is equipped with a polarized or 
grounded electrical power cord. The power cord 
will only fit into a grounded, electrical surge 
protection device (not included) or a grounded 
electrical outlet. 

FOR OPTIMUM POWER FOUNDATION 

OPERATION, USE A GROUNDED, 

ELECTRICAL SURGE PROTECTION DEvICE 

(NOT INCLUDED). FAILURE TO USE A 

SURGE PROTECTION DEvICE COULD 

COMPROMISE SAFETY OR CAUSE PRODUCT 

MALFUNCTION.

WARRANty WARNiNg
Do not open any control boxes, motors or 
hand control devices (with the exception of 
the hand control and power down box battery 
compartments). The product warranty will be 
void if these components are tampered with. 
Do not attempt to alter component wiring or 
adjust or modify the structure of the product in 
any way or the warranty will be void. Any repair 
or replacement of bed parts must be performed 
by authorized personnel. 

 

LUbRicAtiON
This product is designed to be maintenance 
free. The lift motors are permanently lubricated 
and sealed—no additional lubrication is 
required. Do not apply lubricant to lift motor 
lead screws or any nylon nuts or the bed may 
inadvertently creep downward from the elevated 
position.

PROdUct RAtiNgS
The bed lift motors are 

not

 designed for 

continuous use. Reliable operation and full life 
expectancy will be realized as long as the lift 
motors do not operate any more than five (5) 
minutes over a thirty (30) minute period, or 
approximately 15% duty cycle. 

Note: massage 

equipped beds are not designed for continuous, 

extended massage operation. Massage systems 

are rated for a maximum of 2 hours of use 

within any 6 hour period.

 Any attempt to 

circumvent or exceed product ratings will 
shorten the life expectancy of the product and 
may void the warranty.
The recommended weight restrictions for Power 
Foundations are as follows: AC equipped - 600 
lb (272 kg) all sizes; DC equipped - 450 lb 
(204 kg) all sizes. The bed will structurally 
support the recommended weight distributed 
evenly across the head and foot sections. This 
product is not designed to support or lift this 
amount in the head or foot sections alone. 

Note: exceeding the recommended weight 

restrictions could damage the bed and void the 

warranty.

For best performance, consumers should enter 
and exit the adjustable bed with the bed in the 
flat (horizontal) position. 

DO NOT SIT ON THE 

HEAD OR FOOT SECTIONS WHILE IN THE RAISED 

POSITION.

UL (Underwriters Laboratories) recognized 
components.
CFR 1633 approved for use with most 
mattresses.
Made in USA.

AdviSORy

Содержание Bronze





















Отзывы: