background image

Power Foundations Owners Manual 99300787-k

4

AdviSORy

READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT

This Power Foundation has been quality engineered with design features to assure comfort and 
safety when operated properly.

fcc cOMPLiANcE
Electrical components are rated for 110/120 
voltage, 60Hz, 3.9 amp. Components meet 
Class B digital device rating (Part 15, FCC 
rules) for residential use. Power Foundations 
generate, use and may radiate radio frequency 
energy. Radio communication may be affected 
if not installed and operated as recommended 
in this manual. Changes or modifications not 
expressively approved by the party responsible 
for compliance could void the user’s authority 
to operate the equipment.

Radio frequency = 310MHz.

LOckiNg cAStER SAfEty fEAtURE 
Many Power Foundations are equipped with 
locking casters to prohibit the bed from 
movement. For best results, place rubber caster 
cups under locking casters when the bed is 
located on smooth or hard surface flooring—it 
is possible for locking caster equipped beds to 
slide without the use of rubber caster cups. 
To activate locking casters, push down on the 
lock tab. To disengage the locking mechanism, 
push up on the lock tab (see illustration below).

locking caster 
          detail

lock

SMALL cHiLdREN / PEtS WARNiNg
After the bed is unboxed, immediately dispose 
of packaging material as it can smother small 
children and pets. To avoid injury, children or 
pets should not be allowed to play under or on 
the bed. Children should not operate this bed 
without adult supervision.

HOSPitAL USE diScLAiMER 
This bed is designed for in-home use only. It 
is not approved for hospital use and does not 
comply with hospital standards. Do not use this 
bed with tent type oxygen therapy equipment, 
or use near explosive gases.

PAcEMAkER WARNiNg
This product produces a vibrating sensation. 
It is possible that individuals with heart-assist 
pacemakers may experience a sensation similar 
to exercise. Consult physician for complete 
information.

SERvicE REqUiREMENtS
Service technicians are not responsible for 
moving furniture, removing headboards and 
footboards or any items required to perform 
maintenance on the bed. In the event the 
technician is unable to perform service due 
to lack of accessibility, the service call will 
be billed to the purchaser and the service will 
have to be rescheduled.

important information

Содержание Bronze





















Отзывы: