LANDTEC GEM2000 Скачать руководство пользователя страница 19

Страница: 19 / 114

GEM2000 Range Gas Analysers

OMGEMN1.41



Page 19

5.3 Instrument Connection Points

Right Side View:

Left Side View:

Right Side View:

Inlet Port & Static Pressure Port

Attach the sample tube to this port to take
a gas sample. Also used to measure the
static pressure.

Differential Pressure Port
(Blue Port)

Attach the sample tube to this port to
measure differential pressure.

Left Side View:

Gas Outlet Port
(Yellow Port)

The gas outlet port is the point at which
the sample gas is expelled. Tubing may
also be attached to the port.

Connector D (Half Moon)

Communications port used to attach the
USB lead for PC-to-analyser connectivity.
Also used to attach the temperature probe
and gas pod.

Connector E

Used to attach the mains charger to the
analyser for charging and also used to
attach an anemometer.

Dust Caps

Dust caps used to protect the connector
points of the instrument.

Содержание GEM2000















































































































Результаты поиска

Содержание GEM2000

Отзывы:

Бренды по названию

Популярные бренды

LANDTEC GEM2000, Руководство по эксплуатации

Результаты поиска

Содержание GEM2000

Отзывы:

Бренды по названию

Популярные бренды