Landoll SOIL MASTER II 1200 Series Скачать руководство пользователя страница 43

Страница: 43 / 54

3-12 LUBRICATION

The 1200 Series Soil Master II must be lubri-

cated before using it for the first time, and at regu-

lar intervals thereafter. Use a standard multi-

purpose grease.

(See Section 4-8)

to lubricate

your 1200 Series Soil Master II.

3-13 DECAL PLACEMENT

Decals are extremely important for naming pur-

poses and for alerting others to the presence of

the machine. PLACE ALL DECALS on the Soil

Master II as shown in

Figures 3-14 and 3-15.

Center them as nearly as possible between the top

and bottom on the frame bar. Sometimes, shank

spacing may position a tool frame too near the end

of the frame bar to place a reflective tape square

exactly as shown. Then place the square between

the U-bolts on the tool frame as near the proper lo-

cation as possible. A red reflective square is at-

tached to the rear of the left- and right-hand end

tool frames at the factory. If any decals become

unreadable, or are destroyed during use, get re-

placement decals from your Landoll dealer as soon

as possible, and replace them on the machine.

3-26

Содержание SOIL MASTER II 1200 Series























































Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды

Landoll SOIL MASTER II 1200 Series, Руководство оператора

Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды