Landoll SOIL MASTER II 1200 Series Скачать руководство пользователя страница 26

Страница: 26 / 54

3-5 HYDRAULIC LIFT ASSEMBLY - RIGID MODELS

DANGER

TO PREVENT ACCIDENTAL LOWER-

ING OF EQUIPMENT, ALL HYDRAULI-

CALLY ELEVATED EQUIPMENT MUST

BE LOCKED OUT USING THE CYLIN-

DER LOCKOUTS OR LOWERED TO

THE GROUND DURING SERVICING OR

WHEN EQUIPMENT IS IDLE. FAILURE

TO TAKE PREVENTATIVE MEASURES

AGAINST ACCIDENTAL LOWERING

CAN RESULT IN SERIOUS PERSONAL

INJURY OR DEATH.

3-5.1

Unscrew yoke from master cylinder piston

rod, except on 13 shank machines. Install

stroke control cover and stroke control on

cylinder piston rod. Replace cylinder yoke,

adjust extended length to 28-1/4" from hole

center to hole center by threading yoke on

piston rod proper distance. Tighten set screw

to lock yoke in place

(See Figure 3-5)

3-5.2

On 13 shank units, adjust extended cylin-

der length to 28-1/4" from center of pin

holes. Tighten set screw to lock yoke in

place. Cylinder stops are used on the 13

shank Soil Master II.

3-5.3

Install cylinders with ports up on frame.

Connect yoke to gauge wheel arm using cyl-

inder lockouts, extended cylinder pin, and

hair pin cotters. Connect anchor end to main

frame with extended cylinder pin and hair pin

cotters

(See Figures 3-3 and 3-4).

3-5.4

On 13 shank units, lock out for 2" rod must

be on larger cylinder (master).

3-5.5

Install hydraulic lines as shown in

Table

3-1

and

Figure 3-5.

Use 90

elbows in cylin-

der ports.

3-9

Содержание SOIL MASTER II 1200 Series























































Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды

Landoll SOIL MASTER II 1200 Series, Руководство оператора

Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды