Landoll SOIL MASTER II 1200 Series Скачать руководство пользователя страница 18

Страница: 18 / 54

ASSEMBLY INSTRUCTIONS

It is very important that your new 1200 Series

Soil Master II be properly assembled, adjusted and

lubricated before use. Illustrations to assist with the

assembly process are provided in

Section 2,

“Standard Specifications”

. They show proper

shank spacings. Illustrations in this section show

proper assembly procedures. Remove paint from

grease fittings. Replace any grease fittings that are

damaged or missing. Be sure to return screws,

clips, etc.,to their original locations.

To insure alignment of assemblies,

leave the

nuts loose until completion

of final assembly.

Use lock washers or flatwashers as specified.

Spread all cotter pins.

After completion

of final assembly,

tighten all

nuts evenly

to prevent misalignment, distortion or

binding. Tighten all screws and nuts to the recom-

mended torques shown in

Tables 2-1 and 2-2.

DANGER

COULTER BLADES ARE EXTREMELY

SHARP. EXERCISE EXTREME CARE

WHEN WORKING ON OR NEAR COUL-

TER BLADES. DO NOT ALLOW COUL-

TERS TO ROLL OVER OR FALL ONTO

ANY BODILY PART. DO NOT ALLOW

WRENCHES TO SLIP WHEN WORKING

NEAR DISC BLADES. NEVER PUSH

WRENCHES TOWARD COULTER

BLADES. DO NOT CLIMB OVER MA-

CHINE ABOVE COULTER BLADES.

FAILURE TO STAY CLEAR OF COUL-

TER BLADE EDGES CAN CAUSE SERI-

OUS PERSONAL INJURY OR DEATH.

WARNING

DO NOT ATTEMPT TO LIFT HEAVY

PARTS (SUCH AS THE FRAME, COUL-

TER GANGS, AND PULL HITCH)

MANUALLY. USE A HOIST OR A FORK

LIFT TO MOVE THESE PARTS INTO

POSITION.

DANGER

TO PREVENT ACCIDENTAL LOWER-

ING:

1. ALL HYDRAULICALLY ELEVATED

EQUIPMENT MUST BE LOCKED OUT

USING THE CYLINDER LOCKOUTS.

2. LOWER EQUIPMENT TO THE

GROUND WHILE SERVICING OR

WHEN IT IS IDLE.

FAILURE TO TAKE MEASURES TO

PREVENT ACCIDENTAL LOWERING

MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH.

CAUTION

BE SURE TO BLEED THE HYDRAULIC

SYSTEM OF ALL AIR IN LINES AFTER

INSTALLATION. FAILURE TO BLEED

THE SYSTEM OF ALL AIR CAN RE-

SULT IN IMPROPER MACHINE OPERA-

TION.

DANGER

NEVER STAND UNDER OR NEAR THE

HYDRAULIC FOLDING WINGS DURING

FOLDING OR UNFOLDING OPERA-

TIONS. THE WINGS CAN DROP VERY

QUICKLY RESULTING IN SERIOUS IN-

JURY OR DEATH TO ANYONE UNDER

OR NEAR THE CULTIVATOR WINGS.

3-1

Содержание SOIL MASTER II 1200 Series























































Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды

Landoll SOIL MASTER II 1200 Series, Руководство оператора

Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды