Landoll SOIL MASTER II 1200 Series Скачать руководство пользователя страница 44

Страница: 44 / 54

OPERATION AND MAINTENANCE

DANGER

NEVER ALLOW ANYONE TO RIDE ON

THE 1200 SERIES SOILMASTER II AT

ANY TIME. ALLOWING A PERSON TO

RIDE ON THE MACHINE CAN INFLICT

SERIOUS PERSONAL INJURY OR

DEATH TO THAT PERSON.

DANGER

COULTER BLADES ARE EXTREMELY

SHARP. EXERCISE EXTREME CARE

WHEN WORKING ON OR NEAR COUL-

TER BLADES. DO NOT ALLOW COUL-

TERS TO ROLL OVER OR FALL ONTO

ANY BODILY PART. DO NOT ALLOW

WRENCHES TO SLIP WHEN WORKING

NEAR COULTER BLADES. DO NOT

CLIMB OVER MACHINE ABOVE COUL-

TER BLADES. FAILURE TO STAY

CLEAR OF COULTER BLADE EDGES

CAN CAUSE SERIOUS PERSONAL IN-

JURY OR DEATH.

WARNING

ALL HYDRAULICALLY ELEVATED

EQUIPMENT MUST HAVE CYLINDER

LOCKOUTS INSTALLED OR BE LOW-

ERED TO THE GROUND, WHEN SERV-

ICING OR WHEN EQUIPMENT IS IDLE.

FAILURE TO TAKE PREVENTIVE

MEASURES AGAINST ACCIDENTAL

LOWERING CAN RESULT IN SERIOUS

PERSONAL INJURY.

DANGER

NEVER STAND UNDER OR NEAR THE

HYDRAULIC FOLDING WINGS DURING

FOLDING OR UNFOLDING OPERA-

TIONS. THE WINGS MAY DROP VERY

QUICKLY RESULTING IN SERIOUS IN-

JURY OR DEATH TO ANYONE UNDER

OR NEAR THE WINGS.

CAUTION

WHEN TRANSPORTING FARM IMPLE-

MENTS ON PUBLIC ROADS, IT IS THE

RESPONSIBILITY OF THE OPERATOR

TO ABIDE BY STATE AND LOCAL

LAWS CONCERNING WIDE LOADS,

SPEED, SAFETY EMBLEMS AND

SAFETY LIGHTING EQUIPMENT.

DRIVE AT SAFE SPEEDS. PARTICU-

LARLY WHEN ROUNDING CORNERS,

CROSSING ROUGH GROUND OR

DRIVING ON HILLSIDES, TO PREVENT

TIPPING THE TRACTOR.

4-1

Содержание SOIL MASTER II 1200 Series























































Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды

Landoll SOIL MASTER II 1200 Series, Руководство оператора

Результаты поиска

Содержание SOIL MASTER II 1200 Series

Отзывы:

Похожие инструкции для SOIL MASTER II 1200 Series

Бренды по названию

Популярные бренды