4-2
F-808-R0
OPERATING THE B40I4 FORKLIFT
DANGER
Before you operate your Bendi B40i4 forklift, familiarize
yourself with the controls and indicators. Practice going
forward, backward, turning, stopping and parking without
a load on the truck. After you become familiar with the
truck’s operation, learn how to load and unload the
forklift.
As the truck operator, you are responsible for observing
all speed restrictions and traveling in accordance with
aisle and work area conditions.
You are responsible for observing all instructions and
safety regulations during your daily work routine related
to the use of this truck.
It is your responsibility to thoroughly read the Operator’s
Manual, paying particular attention to Chapter 1,
primarily devoted to Safety, before attempting to operate
this truck.
Under normal driving conditions, speed must be chosen
according to the situation, such as surface conditions,
visibility, people working in the area, moving and fixed
objects in the area, cross aisles, etc.
Where visibility is restricted, always travel at very slow
speed and ask for a helper (“Banksman”) to guide you
through the area.
Getting On and Off the Forklift
Always maintain a three-point contact when you get on
and off the forklift. Use the steps and hand grips provided
for this purpose.
Driving Position
DANGER
For proper seating position:
1.
Adjust the driving seat for comfortable operation of
the forklift controls. See Figure 4-6. You must be
correctly seated with all body parts inside the cab.
2.
Fasten your seat belt. See Figure 4-5.
DANGER
Starting and Traveling
Failure to follow this procedure will result in traction not
being enabled.
1.
Make sure the LPG tank is properly mounted and
connected. Open tank valve slightly until pressure
equalizes. Then open the valve the rest of the way.
2.
Sit in the seat and face forward. Be sure the parking
brake is applied.
3.
Set the direction lever to neutral. See Figure 4-4.
4.
Turn the Keyswitch to the Start position, when engine
has started, release and allow Keyswitch to return to
on, run position.
5.
Use the operator controls to raise the forks from the
ground and tilt the mast back. According to ANSI
B56.1, travel with the forks as low to the ground as
possible. This is the recommended traveling position.
WARNING
6.
Hold the steering knob firmly with your left hand.
7.
Release the parking brake.
8.
Set the direction of travel.
9.
Gently depress the drive pedal as required to achieve
a safe operating speed.
Look in the direction you will travel before you
begin to drive the forklift.
Failure to look in the direction you are traveling
can cause serious injury or death.
• Only operate the vehicle from the operator’s
seat with the seat belt fastened.
• Do not place any part of your body outside
the vehicle.
• Do not carry passengers.
• Failure to follow these guidelines can result in
serious injury or death.
Remain in your seat with the seatbelt fastened
while the truck is moving. Your seatbelt will help
you remain inside of the truck should it tip over.
Never jump from the truck if it begins to tip. The
truck may land on you causing serious injury or
death.
Driving with the mast in the traveling position
improves driver visibility and improves the
stability of the truck by reducing the possibility of
personal injury or damage to the load.
Содержание Bendi B40i4
