Landa PGHW5-5000, Руководство оператора

Страница: 12 / 38

12
OPERA
TOR’S MANU
AL
PRESSURE W
ASHER
LANDA PGHW 5-5000 • 8.913-928.0 • REV. 3/13
MAINTENANCE
PREVENTATIVE MAINTENANCE
❑
Check to see that water pump is properly lubri-
cated.
❑
Follow winterizing instructions to prevent freeze
damage to pump and coils.
❑
Always neutralize and flush detergent from system
after use.
❑
If water is known to be high in mineral content, use
a water softener on your water system, or de-scale
as needed.
❑
Do not allow acidic, caustic or abrasive fluids to be
pumped through system.
❑
Always use high grade quality cleaning products.
❑
Never run pump dry for extended periods of
time.
❑
Use clean fuel-kerosene, No. 1 fuel oil, or diesel.
❑
Clean or replace fuel filter every 100 hours of
operation.
❑
Avoid water contaminated fuel as it will damage
the fuel pump.
❑
If machine is operated with smoky or eye burning
exhaust, coils soot up and prevent water from
reaching maximum operating temperature.
❑
Never allow water to be sprayed on or near the
engine or burner assembly or any electrical com-
ponent.
❑
Periodically delime coils per instructions.
❑
Check to see that engine is properly lubricated.
It is advisable, periodically, to visually inspect the
burner. Check air inlet to make sure it is not clogged
or blocked. Wipe off any oil spills and keep this equip-
ment clean and dry.
The flow of combustion and ventilating air to the burner
must not be blocked or obstructed in any manner.
The area around the Landa washer should be kept
clean and free of combustible materials, gasoline and
other flammable vapors and liquids.
MAINTENANCE & SERVICE
Unloader Valves
Unloader valves are preset and tested at the factory
before shipping. Tampering with the factory setting may
cause personal injury and/or property damage, and will
void the manufacturers warranty.
Winterizing Procedure
Damage due to freezing is not covered by warranty.
Adhere to the following cold weather procedures when-
ever the washer must be stored or operated outdoors
under freezing conditions. During winter months, when
temperatures drop below 32°F, protecting your machine
against freezing is necessary. Store the machine in a
heated room. If this is not possible then mix a 50/50
solution of antifreeze and water in the float tank. Turn
the engine on to siphon the antifreeze mixture through
the machine. If compressed air is available, an air fit-
ting can be screwed into the float tank by removing the
float tank strainer and fitting. Inject the compressed air.
Water will be blown out of the machine when the trigger
on the spray gun is opened.
High Limit Hot Water Thermostat
For safety, each machine is equipped with a tempera-
ture sensitive high limit control switch. In the event that
the water should exceed its operating temperature, the
high limit control will turn the burner off until the water
cools then automatically reset itself. The thermostat
sensor is located on the discharge side of the heat-
ing coil. The thermostat control dial is located on the
control panel.
Pumps
Use only SAE 30 weight non-detergent oil. Change
oil after first 50 hours of use. Thereafter, change oil
every three months or at 500 hour intervals. Oil level
should be checked through use of dipstick found on top
of pump, or the red dot visible through the oil gauge
window. Oil should be maintained at that level.
Cleaning of Coils
In alkaline water areas, lime deposits can accumulate
rapidly inside the heating coil. This growth is increased
by the extreme heat build up in the coil. The best
prevention for liming conditions is to use high quality
cleaning chemicals. In areas where alkaline water is
an extreme problem, periodic use of Landa Deliming
Powder (Landa Part #9-028008) will remove lime and
other deposits before coil becomes plugged.
Deliming Coils
Periodic flushing of coils or optional float tank is rec-
ommended.
Step 1 Fill a container with 4 gallons of water, then
add 1 lb. of deliming powder. Mix thoroughly.
Pour mixture into float tank.
Step 2 Remove wand assembly from spray gun and
put spray gun into float tank. Secure the trig-
ger on the spray gun into the open position.
Step 3 Turn engine on, allowing solution to be
pumped through coils back into the float tank.
The solution should be allowed to circulate
2-4 hours or until the color changes.
Step 4 After circulating solution, flush the entire
system with fresh water. Clean out float tank
and then reinstall wand assembly to spray
gun.