Land Pride RCR2596 Series Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 56

background image

Table of Contents

©

Copyright 2020 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

7/29/20

RCR2596, RCR2510, and RCRM2510 Rotary Cutters 312-753M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . 11
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . 11

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Section 1: Assembly & Set-up . . . . . . . . . . . 12

Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . 12

Pull-Type Hitch . . . . . . . . . . . . . . . . . . . . . . . . . 12
3-Point Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Dealer Preparations . . . . . . . . . . . . . . . . . . . . . . . 12
Gearbox Vent Plugs & Dipsticks . . . . . . . . . . . . . . 13

Vent Plug Installation . . . . . . . . . . . . . . . . . . . . . 13

Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . 13
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . 13
Pull-Type Cutter   . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Hitch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 14
Equal Angle Driveline Installation . . . . . . . . . . . . 15
Constant Velocity Driveline Installation . . . . . . . 16
Pull-Type Hook-Up . . . . . . . . . . . . . . . . . . . . . . . 17

3-Point Lift-Type Cutter . . . . . . . . . . . . . . . . . . . . . 18

Hitch Assembly   . . . . . . . . . . . . . . . . . . . . . . . . . 18
Driveline Installation . . . . . . . . . . . . . . . . . . . . . . 18
3-Point Hook-Up   . . . . . . . . . . . . . . . . . . . . . . . . 19
Driveline Hook-up   . . . . . . . . . . . . . . . . . . . . . . . 20
Check Driveline Collapsible Length  . . . . . . . . . . 22
Check Driveline Interference  . . . . . . . . . . . . . . . 23

Check Chains (Accessory) . . . . . . . . . . . . . . . . . . 23

Section 2: Assembly of Optional Equipment 24

Chain Safety Guards (Optional) . . . . . . . . . . . . . . 24
Rubber Safety Guards (Optional) . . . . . . . . . . . . . 25

Section 3: Adjustments . . . . . . . . . . . . . . . . . 26

Pull-Type Leveling & Cutting Height . . . . . . . . . . . 26

Deck Leveling From Front to Back . . . . . . . . . . . 26
Pull-Type Cutting Height . . . . . . . . . . . . . . . . . . 26

3-Point Leveling & Cutting Height . . . . . . . . . . . . . 27

Deck Leveling From Left to Right  . . . . . . . . . . . . 27
Deck Leveling From Front to Rear  . . . . . . . . . . . 27
Center Link Adjustment  . . . . . . . . . . . . . . . . . . . 27
Tailwheel Height Adjustment  . . . . . . . . . . . . . . . 28

Section 4: Operating Procedures . . . . . . . . . 29

Operating Checklist  . . . . . . . . . . . . . . . . . . . . . . . . 29
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 29
Inspection of Tractor & Cutter  . . . . . . . . . . . . . . . . 30
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Blade Engagement & Disengagement . . . . . . . . . . 31

Blade Engagement . . . . . . . . . . . . . . . . . . . . . . . 31
Blade Disengagement . . . . . . . . . . . . . . . . . . . . 31

Field Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turning Angles for Pull-Type Cutters . . . . . . . . . . . 32
Crossing Steep Ditches & Banks . . . . . . . . . . . . . . 32
Unhook 3-Point Cutter  . . . . . . . . . . . . . . . . . . . . . . 33
Unhook Pull-Type Cutter  . . . . . . . . . . . . . . . . . . . . 33
General Operating Instructions  . . . . . . . . . . . . . . . 34

Section 5: Maintenance & Lubrication . . . . . 35

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Hydraulic System   . . . . . . . . . . . . . . . . . . . . . . . . . 35
Tires   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Skid Shoe Maintenance . . . . . . . . . . . . . . . . . . . . . 36
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 36
Driveline Slip-Clutch   . . . . . . . . . . . . . . . . . . . . . . . 38
RCR2596 Dual End Flex Couplers   . . . . . . . . . . . . 40
RCR(M)2510 Dual End Flex Couplers . . . . . . . . . . 40
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 41
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 41
Lubrication Points  . . . . . . . . . . . . . . . . . . . . . . . . . 42

3-Point Tailwheel Spindle Tube  . . . . . . . . . . . . . 42
Tailwheel Hub   . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Pillow Block Bearing (Pull-Type Cutter)  . . . . . . . 42
Ratchet Jack   . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
T-Gearbox   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Dual End Flex Coupler  . . . . . . . . . . . . . . . . . . . . 43
Driveline U-Joints  . . . . . . . . . . . . . . . . . . . . . . . . 44
CV Driveline U-Joints & Profile Shields   . . . . . . . 44
Driveline Profiles With Grease Zerk  . . . . . . . . . . 44
Driveline Profiles Without Grease Zerk   . . . . . . . 44

Section 6: Specifications & Capacities  . . . . . 45
Section 7: Features and Benefits   . . . . . . . . . 48
Section 8: Troubleshooting  . . . . . . . . . . . . . . 49
Section 9: Torque & Tire Inflation Charts  . . . 50
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 51

«
1
2
3
4
5
...
»

Содержание RCR2596 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для RCR2596 Series

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: Gardigo Страницы: 24

Бренд: Gardner Bender Страницы: 8

Бренд: Garantia Страницы: 4

Бренд: NARIKA Страницы: 2

SeQual Eclipse 5

Бренд: CAIRE Страницы: 2

Бренд: Mindray Страницы: 295

Бренд: ZAMST Страницы: 14

Бренд: Cotech Страницы: 44

SciCan STATIM 2000S

Бренд: Coltene Страницы: 45

Бренд: Chroma Страницы: 198

Бренд: Toro Страницы: 2

Бренд: ALLSPEEDS Страницы: 22

Бренд: Sonotron NDT Страницы: 94

2 ST VERTICAL CHEST

Бренд: Nautilus Страницы: 11

Бренд: Avid Technology Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды