Land Pride RCR2596 Series Скачать руководство пользователя страница 24

Страница: 24 / 56

Section 1: Assembly & Set-up

RCR2596, RCR2510, and RCRM2510 Rotary Cutters 312-753M

Table of Contents

7/29/20

5. Attach cutter to lower 3-point lift arms as follows:

RCR2596 With Cat. I Tractor Hitch

a. Discard bushings (#3 & #4).
b. Insert hitch pins (#2A) through hitch hole “A” first

and then hitch hole “B”.

c. Slide lower 3-point lift arm hitch holes over end of

hitch pins (#2A).

Refer to Figure 1-11:

RCR2596 With Cat. II Tractor Hitch

a. Discard bushings (#3 & #4).
b. Insert hitch pins (#2A) through hitch hole “A”, lower

3-point arm hitch holes, and then hitch hole “B”.

RCR2510 & RCRM2510 With Cat. II Tractor Hitch

a. Discard bushing (#3).
b. Insert hitch pins (#2B) through hitch hole “B”, lower

3-point arm hitch holes, bushing (#4), and then

hitch hole “A”.

RCR2510 & RCRM2510 With Cat. III Tractor Hitch

a. Place bushing (#3) inside lower 3-point lift arm

hitch holes.

b. Insert hitch pins (#2B) through lower hitch

hole “B”, bushing (#3), bushing (#4), and then

through hitch hole “A”.

6. Secure hitch pins (#2A or #2B) with linchpins (#1).
7.

Connect top center 3-point link to the upper pivot

hitch using 1" clevis pin (#6), flat washer (#7), and

cotter pin (#5). Bend on or both legs of cotter pin to

prevent it from falling out.

8. The center 3-point link should be adjusted to allow for

lateral float. Please consult you tractor’s manual for

adjusting instructions.

9. Adjust stabilizers on the tractor’s lower 3-point arms

to stop lateral float. Please consult your tractor’s

manual for adjusting instructions.

Driveline Hook-up

Refer to Figure 1-11:

DANGER

To avoid serious injury or death:

•

Do not engage power take-off while hooking-up or

unhooking the driveline, or while someone is standing near

the driveline. A person’s body and/or clothing can become

entangled in the driveline.

•

All guards and shields must be installed and in good

working condition while operating the implement.

•

Do not use a power take-off adapter. The adapter will

increase strain on the tractor’s power take-off shaft causing

possible damage to shaft and driveline. It will also defeat

the purpose of the tractor’s power take-off shield.

•

Make certain driveline yokes are securely fastened at each

end. A loose yoke can work free allowing the driveline to

rotate uncontrollably causing implement damage and

bodily injury or death to anyone nearby.

WARNING

To avoid serious injury or death:

•

Always follow “Tractor Shutdown Procedure” provided in

this manual before dismounting the tractor.

•

Check driveline when lowering implement to make sure it

does not interfere with the tractor drawbar at maximum

depth. If needed, shut tractor off and move or remove

drawbar to prevent driveline damage.

3-Point Lift Type Cutter Tractor Hook-Up

Figure 1-11

22293

37298

Содержание RCR2596 Series

























































Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды

Land Pride RCR2596 Series, Руководство оператора

Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды