Land Pride RCR2596 Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 56

background image

37

Section 5: Maintenance & Lubrication

RCR2596, RCR2510, and RCRM2510 Rotary Cutters 312-753M

Table of Contents

7/29/20

Blade Positioning and Rotational Directional

Figure 5-3

Refer to Figure 5-3:

9. Make certain when installing cutter blades that the

blades on one spindle is positioned 90 degrees to the

blades on the other spindle as shown in Figure 5-3.

10. Carefully check cutting edges of blades in relation to

blade rotation to ensure correct blade placement.

Blade rotation is counterclockwise on the left side

and clockwise on the right side as shown. Airfoil (lift)

must be oriented towards the top of the deck.

Refer to Figure 5-4:

WARNING

!

To avoid serious injury or death:
A locknut that has been removed can lose its thread locking

properties. Reusing a used locknut can result in a thrown

blade. Always use a new locknut when installing blades.

11. Insert blade bolt (#1) through blade (#6), dish

pan (#4), and flat washer (#2). Secure blade with a

new locknut (#3)

and torque to 450 ft-lb.

12. Repeat step 11 for the other blade.
13. Replace access cover (#5).
14. If replacing dishpan (#4), nut (#7) on gearbox output

shaft should be torqued to 450 ft-lbs. minimum and

cotter pin (#8) installed with both legs bent opposite

directions around nut (#7).

C

C

W

CW

IMPORTANT:

Examine blade bolts (#1) and flat

washers (#2) for excessive wear and replace if worn.

Cutter Blade Assembly

Figure 5-4

35941

Land Pride Cutter Blade Parts

# Part No. Part Description

318-586A BLADE BOLT KIT . . (items 1, 2, & 3 below)

1 802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY
2 804-147C WASHER FLAT 1 HARD ASTMF436
3 803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE
4 312-881H 27 x 10G OVAL DISHPAN WELDMENT
5 840-273C PLUG LP 3" ID RUBBER
6 820-168C SEE LIST OF CUTTER BLADES BELOW

Land Pride List of Cutter Blades

Part No.

Part Description

820-614C RCF3096 CUTTER BLADE 1/2 x 4 x 20.5 CCW
820-615C RCF3096 CUTTER BLADE 1/2 x 4 x 20.5 CW
820-137C RCR2510 CUTTER BLADE 1/2 x 4 x 25 CCW
820-112C

RCR2510 CUTTER BLADE 1/2 x 4 x 25 CW

Optional Low Lift Cutter Blades

820-210C RCR2596 BLADE 1/2X4X20.5 LL CCW
820-211C RCR2596 BLADE 1/2X4X20.5 LL CW
820-193C RCR2510 BLADE 1/2X4X25 LL CCW
820-209C RCR2510 BLADE 1/2X4X25 LL CW

Use 1-11/16" Socket Wrench On Blade Nut (#3)

«
...
39
40
41
42
43
...
»

Содержание RCR2596 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для RCR2596 Series

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Harken Страницы: 4

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: ubbink Страницы: 30

Бренд: Fast Страницы: 60

Бренд: Additel Страницы: 107

Бренд: ubicquia Страницы: 36

Бренд: Yacht Devices Страницы: 32

CHIEFTAIN E1006

Бренд: Falcon Страницы: 5

SeQual Eclipse 5

Бренд: CAIRE Страницы: 2

Monster Truck Headboard 41903

Бренд: Simplay3 Страницы: 4

MERLIN N Series

Бренд: Meheen Страницы: 24

Бренд: Williams Sound Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды