Land Pride RCR2596 Series Скачать руководство пользователя страница 29

Страница: 29 / 56

Section 2: Assembly of Optional Equipment

RCR2596, RCR2510, and RCRM2510 Rotary Cutters 312-753M

Table of Contents

7/29/20

Rubber Safety Guards (Optional)

DANGER

To avoid serious injury or death:
Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front & rear safety guards is

mandatory with this cutter. Stop blade rotation if bystanders

are in or around the area. It is recommended that a safety

shield be placed between the operator and cutter on an open

air tractor.

WARNING

To avoid serious injury or death:
Keep all safety guards in place. Rotary Cutters have the

ability to discharge objects at high speeds. Use extreme

caution when cutting in areas where people may be present. It

is best to operate the cutter when no one is nearby. Stop blade

rotation if someone is in or around the area.

Front Rubber Guards

RCR2596 & RCRM2596

Refer to Figure 2-4:

Install front rubber shields (#1) with 1/2" -13 x 2 3/4" long

carriage bolts (#2) and flange nuts (#3) as shown.

Front Rubber Guards

RCR2510 & RCRM2510

Refer to Figure 2-5:

Install front rubber shields (#1) & (#2) with

1/2" -13 x 3 1/2" long carriage bolts (#3) and flange

nuts (#4) as shown.

Rear Rubber Guards

Refer to Figure 2-6:

Install rear rubber shield (#1) and rear shield strap (#2)

with 1/2" -13 x 1 1/2" long carriage bolts (#3) and

1/2" flange nuts (#4) as shown.

NOTE:

Do not tighten hardware until assemblies

are complete. Refer to

“Torque Values Chart”

page 50.

RCR2596 Front Rubber Shields

Figure 2-4

RCR2510 & RCRM2510 Front Rubber Shields

Figure 2-5

Rear Rubber Shield

Figure 2-6

22307

22308

16266

Содержание RCR2596 Series

























































Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды

Land Pride RCR2596 Series, Руководство оператора

Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды