Land Pride RCR2596 Series Скачать руководство пользователя страница 17

Страница: 17 / 56

Section 1: Assembly & Set-up

RCR2596, RCR2510, and RCRM2510 Rotary Cutters 312-753M

Table of Contents

7/29/20

Gearbox Vent Plugs & Dipsticks

Vent Plug Installation

Refer to Figure 1-2 & Figure 1-3:

Vent plugs are shipped loose and packaged with the

Operator’s Manual. Remove temporary solid plugs on top

of gearboxes and replace with included 3/8" vent plug.

See your nearest Land Pride dealer if vent plugs are

missing.

Torque Requirements

Refer to

“Torque Values Chart”

on page 50 to

determine correct torque values for common bolts. See

“Additional Torque Values”

at bottom of chart for

exceptions to standard torque values.

Tractor Shutdown Procedure

The following are basic tractor shutdown procedures.

Follow these procedures and any additional shutdown

procedures provided in your tractor Operator’s Manual

before leaving the operator’s seat.
1. Reduce engine speed and disengage power take-off

if engaged.

2. Park tractor and implement on level, solid ground.
3. Lower implement to ground or onto non-concrete

support blocks.

4. Put tractor in park or set park brake, turn off engine,

and remove switch key to prevent unauthorized

starting.

5. Relieve all hydraulic pressure to auxiliary hydraulic

lines.

6. Wait for all components to come to a complete stop

before leaving the operator’s seat.

Use steps, grab-handles and anti-slip surfaces when

stepping on and off the tractor.

IMPORTANT:

Gearboxes are shipped with solid

plugs in them to prevent oil loss during shipping and

handling. The solid plug on top of the gearbox must

be replaced with a vented dipstick before operating

the implement.

‘

T-Gearbox

Figure 1-2

Blade Drive Gearboxes

Figure 1-3

22320

Remove 3/8" T-Box Solid

Plug & Install Vent Plug

DO NOT

OVERFILL!

30216

DO NOT

OVERFILL!

Oil Level

Plug

Remove 3/8" Solid Plug &

Install Vent Plug

Содержание RCR2596 Series

























































Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды

Land Pride RCR2596 Series, Руководство оператора

Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды