Land Pride RCR2596 Series Скачать руководство пользователя страница 44

Страница: 44 / 56

Section 5: Maintenance & Lubrication

RCR2596, RCR2510, and RCRM2510 Rotary Cutters 312-753M

Table of Contents

7/29/20

Flex Couplers

Figure 5-8

RCR2596 Dual End Flex Couplers

Refer to Figure 5-8:

Replace two rubber discs (#1), (Land Pride Part No.

19-075), as follows: If additional repair parts are required,

refer to Land Pride’s Parts Manual 326-566P.

1. Attach rubber discs (#4) to the double flex yoke (#3)

with 6 bolts (#6A), 12 beaded washers (#1),

6 bushing (#2), and 6 nylock nuts (#7) as shown.

Make sure beads on the beaded washers are facing

the rubber discs. Do not tighten nuts.

2. Attach yoke ends (#5) to rubber discs (#4) with

6 bolts (#6B), 12 beaded washers (#1),

6 bushing (#2), and 6 nylock nuts (#7) as shown.

Make sure beads on the beaded washers are facing

the rubber discs. Do not tighten nuts.

3. Tighten nuts (#7) evenly with nuts torqued 35 to

40 ft-lb. Beaded washers (#2) should be embedded

halfway into the rubber disc.

35085

IMPORTANT:

Make sure beads on beaded washers

(#1) are always facing rubber discs in assembly.

Dual End Flex Couplers

Figure 5-9

RCR(M)2510 Dual End Flex Couplers

Refer to Figure 5-9:

Replace four rubber discs (#4), (Land Pride Part No.

19-075), as follows. If additional repair parts are required,

refer to Land Pride’s Parts Manual 327-088P.

1. Attach rubber discs (#4A) to the double flex yoke (#3)

with 3 bolts (#6A), 12 beaded washers (#1),

6 bushings (#2), and 3 nylock nuts (#7) as shown.

Make sure beads on the beaded washers are facing

the rubber discs. Do not tighten nuts.

2. Attach yoke end (#5) to rubber discs (#4) with

3 bolts (#6B), 12 beaded washers (#1),

6 bushing (#2), and 3 nylock nuts (#7) as shown.

Make sure beads on the beaded washers are facing

the rubber discs. Do not tighten nuts.

3. Tighten nuts (#7) evenly with nuts torqued 35 to

40 ft-lb. Beaded washers (#2) should be embedded

halfway into the rubber disc.

4. Repeat steps 1 thru 3 to install rubber discs (#4B) on

opposite end of flex coupler.

35085

Opposite End

IMPORTANT:

Make sure beads on beaded washers

(#1) are always facing rubber discs in assembly.

Содержание RCR2596 Series

























































Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды

Land Pride RCR2596 Series, Руководство оператора

Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды