Land Pride RCR2596 Series Скачать руководство пользователя страница 20

Страница: 20 / 56

Section 1: Assembly & Set-up

RCR2596, RCR2510, and RCRM2510 Rotary Cutters 312-753M

Table of Contents

7/29/20

RCR2510 & RCRM2510 Constant Velocity Driveline Assembly

Figure 1-7

22304

Constant Velocity Driveline Installation

DANGER

To avoid serious injury or death:
Make certain driveline yokes are securely fastened at each

end. A loose yoke can work free allowing the driveline to

rotate uncontrollably causing implement damage and bodily

injury or death to anyone nearby.

WARNING

To avoid serious injury or death:
Maximum constant velocity driveline turning angle is limited

to 80 degrees Exceeding this angle can cause the driveline to

break and send flying objects.

Refer to Figure 1-7:

Constant velocity driveline can be installed on RCR2510

and RCRM2510 cutters only. Maximum turning angle is

limited to 80 degrees.
1. Unsnap one end of gearbox shield access doors (#7)

and rotate doors open.

2. Remove protective sleeve (#11) from input shaft of

gearbox (#1) and discard.

RCR2510 only:

Remove 2-nuts (#10), 2-lock

washers (#9), and 2-bolts (#8) from slip-clutch end of

driveline (#2).

RCRM2510 only:

Remove 1-nut (#10), 1-lock

washer (#9), and 1-conical dog pin (#8) from slip-

clutch end of driveline (#1).

4. Slide slip-clutch end of driveline onto input shaft of

gearbox (#6) until hole in yoke aligns with notch in

input shaft.

IMPORTANT:

The driveline must be lubricated

before putting it into service. Refer to

“Lubrication

Points”

on page 42.

NOTE:

Do not tighten hardware until assembly or

driveline is complete.

RCR2510 only:

Insert 2-bolts (#10) through holes in

driveline yoke as shown and secure with lock

washers (#9) and nuts (#10).

RCRM2510 only:

Insert 1-conical dog pin (#8)

through hole in yoke and secure with lock

washer (#9) and nut (#10).

6. Tighten nut (#10) to 45-50 ft-lbs of torque.
7.

Push/pull on driveline yoke to be sure it is securely

fastened to the gearbox shaft.

8. Rotate gearbox shield access doors (#7) closed and

snap in place.

9. Fully insert jackshaft driveline (#1) into pillow block

bearing (#7).

10. Secure bearing support (#2) with 1/2"-13 x 3 1/2"

bolts (#3) and hex flange nuts (#4). Do not tighten

nuts (#4) at this time.

11. Remove locknut (#12) and bolt (#13) from bolted

coupler end of driveline (#5).

12. Push bolted coupler end of main driveline (#5) onto

the jackshaft of driveline (#1) as far as possible.

13. Attach driveline (#5) to jackshaft driveline with

removed bolt (#13) and locknut (#12). Tighten

locknut to 45-50 ft-lbs of torque.

14. Tighten nuts (#4) to the proper torque.
15. Rotate locking collar in bearing (#7) clockwise until

tight.

16. Tighten set screw in bearing (#7) locking collar.

NOTE:

Make sure locking collar on bearing (#7) is

facing forward toward the tractor.

Содержание RCR2596 Series

























































Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды

Land Pride RCR2596 Series, Руководство оператора

Результаты поиска

Содержание RCR2596 Series

Отзывы:

Похожие инструкции для RCR2596 Series

Бренды по названию

Популярные бренды