Land Pride RCM3615 страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 64

background image

Section 5: Maintenance & Lubrication

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

43

Table of Contents

5. Shut tractor down before dismounting. Refer to

“Tractor Shutdown Procedure”

6. Disconnect main driveline from the tractor’s power

take-off shaft.

Refer to Figure 5-6:

7.

Remove rubber plug (#5). Rotate blade carrier (#4)
until blade bolt (#1) aligns with access hole (A).

8. Unscrew locknut (#3) to remove cutter blade (#6).

Blade bolt (#1) is keyed and will not turn freely.

9. Both blades should be sharpened at the same angle

as the original cutting edge and must be replaced or
re-ground at the same time to maintain proper
balance in the cutting unit. The following precautions
should be taken when sharpening blades:

a. Do not remove more material than necessary.

b. Do not heat and pound out a cutting edge.

c. Do not grind blades to a razor edge. Leave a blunt

cutting edge approximately 1/16" thick.

d. Always grind cutting edge so end of blade remains

square to cutting edge and not rounded.

e. Do not sharpen back side of blade.

f. Both blades should weigh the same with not more

than 1 1/2 oz. difference. Unbalanced blades will
cause excessive vibration which can damage
gearbox bearings and create structural cracks.

Refer to Figure 5-7:

10. Carefully check cutting edges of blades in relation to

blade carrier rotation to ensure correct blade
placement. Cutter blades must be installed with
cutting edge leading in rotation

.

Refer to Figure 5-6:

WARNING

!

To avoid serious injury or death:
A locknut that has been removed can lose its thread locking

properties. Reusing a used locknut can result in a thrown

blade. Always use a new locknut when installing blades.

11. Insert blade bolt (#1) through blade (#6),

dishpan (#4), and flat washer (#2). Secure blade with
a

new locknut (#3)

and torque to 450 ft-lbs.

12. If replacing dishpan (#4), nut (#7) on gearbox output

shaft should be torqued to 450 ft-lbs. minimum and
secured with cotter pin (#8) with both legs bent
opposite directions around the nut.

13. Replace rubber plug (#5).

14. Reconnect main driveline to tractor power take-off

shaft.

IMPORTANT:

Examine blade bolts and their flat

washers for excessive wear and replace if worn.

Cutter Blade Assembly

Figure 5-6

Direction of Blade Rotation

Figure 5-7

Use 1-11/16"

Socket Wrench

On Blade Nut (#3)

Land Pride Cutter Blade Parts

#

Part No.

Part Description

318-586A BLADE BOLT KIT

(Includes items 1, 2, & 3 below)

1 802-277C BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY
2 804-147C WASHER FLAT 1 HARD ASTMF436
3 803-170C NUT HEX TOP LOCK 1 1/8-12 PLATE
4 312-820H DISHPAN WELDMENT . , 15" CTR (COMER)
5 840-273C PLUG LP 3" ID RUBBER
6 820-112C CUTTER BLADE 1/2x4x25 CW (LH WING)
6 820-137C CUTTER BLADE 1/2x4x25 CCW (RH WING)
6 820-138C CUTTER BLADE 1/2x4x31 CCW (CTR DECK)

37579

CCW

CCW

CW

«
...
45
46
47
48
49
...
»

Содержание RCM3615

































































Отзывы:

Нет отзывов

Похожие инструкции для RCM3615

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Garelick Страницы: 4

Бренд: Haaga Страницы: 31

Бренд: Labnet Страницы: 12

Accublock D1301

Бренд: Labnet Страницы: 13

Бренд: Laser Страницы: 2

Бренд: Lars Thrane Страницы: 50

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Maeda Страницы: 276

Бренд: PASCO Страницы: 5

Бренд: Pasco Scientific Страницы: 27

Бренд: PARUS Страницы: 6

Бренд: Tar River Страницы: 44

Бренд: Tar River Страницы: 61

MiniLift160 Classic

Бренд: Handicare Страницы: 28

Бренд: Hands Free Farm Страницы: 24

Бренд: i-Optik Страницы: 75

Бренд: GE Страницы: 644

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды