Land Pride RCM3615 Скачать руководство пользователя

Страница: 23 / 64

Section 1: Assembly & Set-up

RC3615 and RCM3615 Series 2 S/N Rotary Cutters 330-502M

12/12/18

Table of Contents

Wing Axle - Turnbuckle Assembly

Figure 1-13

Wing Axle Turnbuckle Set-up

Refer to Figure 1-13:

WARNING

To avoid serious injury or death:
Connect turnbuckles (#5) to wing axles (#1) before lowering

wings. Otherwise, personal injury and/or damage to the

turnbuckle can occur.

Park tractor and cutter on a level surface.

2. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 14.

3. Cut metal band between the two wing axles.

4. On the right wing axle, loosen locknuts (#2) slightly to

allow rotation of the axle.

5. Remove locknut (#3) and 1 1/4" hex head bolt (#4).

6. Loosen jam nut (#6) on turnbuckle (#5) and adjust

until center of ball swivels are approximately 10 1/2"
apart. Do not tighten jam nut. Final adjustment will be
made later when leveling wing decks.

Rotate right axle (#1) until turnbuckle (#5) can be
attached to the axle with existing bolt (#4) and
locknut (#3). Tighten locknut (#3) to the correct
torque.

8. Tighten locknuts (#2) until snug. Do not over tighten.

Wing axle must be able to pivot in the field.

9. Repeat steps 4-6 for the left wing axle.

27929

NOTE:

Wing axle locknuts (#2) are tightened for

shipping purposes. They must be loosened slightly
to allow the axle to pivot. Do not torque them tight.

Unfold Wings

DANGER

To avoid serious injury or death:
Keep everyone out of the area where the wing decks will

unfold. One of the wing decks can fall suddenly.

Refer to Figure 1-14:

Park tractor and cutter on a level surface.

2. Raise both wings up to release any tension on

transport lock bars (#3).

3. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 14.

4. Remove hairpin clip (#1) from both the left and right

cylinder pins (#4).

Refer to Figure 1-15:

5. Rotate end of transport lock bar (#3) to the storage

lug (#2) as shown in Figure 3-3 on page 34. Secure
with hairpin clips (#1).

6. Restart tractor and lower both left and right wings

with tractor hydraulic control lever until both wings
are on the ground.

Transport Bar, Locked Position

Figure 1-14

Transport Bar, Storage Position

Figure 1-15

27921

27923

Содержание RCM3615

































































Результаты поиска

Содержание RCM3615

Отзывы:

Похожие инструкции для RCM3615

Бренды по названию

Популярные бренды

Land Pride RCM3615, Руководство оператора

Результаты поиска

Содержание RCM3615

Отзывы:

Похожие инструкции для RCM3615

Бренды по названию

Популярные бренды